Troubleshooting Guide - Technibel Climatisation MPW Série Notice D'utilisation

ACTIVATED CARBON AIR FILTER
• The fi lter is to be mounted in addition to the normal fi lter.
• It is made of two layers:
- the fi rst layer consist in a synthetic honey comb high effi ciency media to remove the dust and purifi ng the air,
- the second layer in coarcoal media deodorizing the ambient air.
Fitting the activated carbon air fi lter.
• MPW
1 - Open the air intake grille and remove the 2 fi lters supplied
with the unit.
2 - Fit the 2 activated carbon fi lters into position as shown in
the illustration ("FRONT" in front).
3 - Replace the 2 fi lters in their housing and close the grille.
• KPSW
1 - Open the unit intake air grille and pull out the standard air
fi lter.
2 - Apply on the rear side of anti-mold fi lter the two springs
supplied with the accessory.
3 - Fix the "air clean" fi lter by the springs.
4 - Insert the two air fi lters one over the other and close the
intake grille.
9 - ADVICE ON COMFORT AND ENERGY SAVING
AVOID:
• Blocking the appliance's air inlet and outlet grilles. If they are
blocked, the appliance will not work satisfactorily and it may
be damaged.
• Allowing the sun to shine directly into the room when the
appliance is operating in "air conditioning" mode. Use shutters
or curtains.

10 - TROUBLESHOOTING GUIDE

• If the air conditioner is not working properly, carry out the following checks before calling the After-Sales Department.
• If the problem persists, contact the After-Sales Department.
PROBLEMS
The air conditioner is not operating at
all (the fan never comes on).
Insuffi cient cooling or heating.
For installations which can operate in
cooling or heating mode:
excessive or non-existent cooling or
heating.
(accessory supplied on request)
KPSW
CHECK:
• That the fi lter is always clean. A clogged fi lter will reduce the
appliance's effi ciency.
• That all doors, windows and other openings are closed in
order to prevent non-cooled air entering when the appliance
is operating in the "cooling" mode.
POSSIBLE CAUSES
1 - Power cut.
2 - Circuit-breaker thrown or fuse blown.
3 - Line voltage too low.
4 - The selector switch is on "0" (off).
5 - The setpoint temperature is set too high
for cooling or too low for heating.
1 - Air fi lter dirty or blocked.
2 - Heat source or too many people in the
room.
3 - Doors and/or windows open.
4 - Obstacle in front of the air inlet or outlet.
5 - The setpoint temperature is set too high
for cooling or too low for heating.
6 - The installation's cold water or hot water
generator is operating incorrectly or not
operating at all.
1 - The thermostat operating mode (heating
or cooling) is not adapted.
2 - The installation's cold water or hot water
generator is operating incorrectly.
MPW
Activated carbon air fi lter
"Air clean" fi lter
(high effi ciency honeycomb
and coarcoal media)
1 - Restore the supply.
2 - Contact the After-Sales Department.
3 - Consult your electrician.
4 - Work the selector switch.
5 - Set the temperature lower (or higher).
1 - Clean the air fi lter.
2 - If possible, eliminate the heat source.
3 - Close them to prevent outside air
entering.
4 - Remove the obstacle in order to provide
good air circulation.
5 - Set the temperature lower (or higher).
6 - Check the operation of the generator.
Contact the After-Sales Department.
1 - Check the mode selected.
2 - Check the operation of the generator.
Contact the After-Sales Department.
Rear side of
anti-mold fi lter
Spring
SOLUTIONS
5
F
GB
I
E
D