Operation; Dry Vacuum Cleaning - SPARKY Professional VC 1650MS Notice Originale

7. Rear wheel fixing bar
8. Spring washer
9. Washer
10. Castor with brake
11. Brake pedal
12. Castor
13. Splint pin
14. Washer
15. Wheel axes
16. Rear wheel
17. Wheel cap
UNPACKING
Due to modern mass production techniques, it is unlikely
that your electric appliance is faulty or that a part is miss-
ing. If you find anything wrong, do not operate the ap-
pliance until the parts have been replaced or the fault
has been rectified. Failure to do so could result in serious
personal injury.
The product is delivered in two separate boxes, one
of them with the vacuum cleaner, the other one -
with the Hand trolley.
Carefully unpack the contents of the box.
1. Hold the two clamps (18) fastening the upper section
(2) in its position and fold them upwards (Fig.3).
2. Loosen the clamps, remove the upper section (Fig.4)
and take out the contents from the tank (Fig.5).
Please check the parts using the list shown above to
make sure they are complete and that there has been no
damage in transport.
ASSEMBLY
Vacuum Cleaner
▪ Make sure that the cable is unplugged (Fig.2).
▪ Hold the two clamps, which hold the upper section in
its position and fold them upwards (Fig.3).
▪ Loosen the clamps and lift the upper section up and
out (Fig.4).
▪ For wet vacuum cleaning fit the supplied foam filter
(Fig.6а).
▪ For dry vacuum cleaning fit the supplied pleated poly-
ester filter (Fig.6c) or the dust bag (Fig.6b).
▪ Place the upper section back on the tank (Fig.7).
▪ Align the upper section with the clamps and snap into
place by applying pressure in the middle point of the
clamps (Fig.8).
Assemble the Hand trolley as described below.
▪ Hold the left and the right tank grips. Assemble the
vacuum cleaner hinge bar onto the round bar parallel
to the ground (Fig.9).
▪ Insert the large end of the hose into the front tank inlet
and fasten it securely (Fig.10).
▪ Choose the appropriate nozzle or metal tube and in-
stall them on the hose (Fig. 11).
Hand trolley
1. Pull out the upper handle (Fig.12).
2. Unfold the base until it is fixed with the middle part
(Fig.13).
3. Fix the upper handle (Fig.14).
4. Assemble the castors. Insert one or two washers
to adjust the distance so that the castors touch the
ground (Fig.15).
Original instructions
5. Assemble the rear wheels. Place the axes into the
wheels on both sides of the shaft and place the split
pins to fix them (Fig.16). Put the wheel caps (17) on.
6. The hand trolley is ready for use (Fig.17).
V - Operation instructions
This electric appliance is supplied from single-phase al-
ternating current mains only. The vacuum cleaner must
be connected to grounded sockets. This electric appli-
ance is radio suppressed in compliance with EMC Direc-
tive 2004/108/EC.
This electric appliance is designed to vacuum the dust
generated during operating a power tool. For this pur-
pose model VC 1650MS is equipped with a built-in sock-
et (11), for inserting the cable plug of the power tool. The
vacuum cleaner will switch on automatically as soon as
you switch on the power tool. When you switch off the
power tool, the vacuum cleaner will also switch off after
a pre-set delay.
PRIOR TO INITIAL OPERATION
▪ Make sure power supply voltage corresponds to the
value indicated on the name plate with technical data
of the appliance.
▪ If the supply cord is damaged it must be replaced with
a special cord or assembly available from the manu-
facturer or its service agent to avoid a safety hazard.
▪ It is absolutely necessary for you to read, understand,
and observe the section entitled "Safety instructions
for vacuum cleaners".

DRY VACUUM CLEANING

WARNING: Never vacuum up hazardous ma-
terials.
If an incorrect dust bag is used, then the guarantee be-
comes void.
▪ Make sure that the appliance is not plugged into the
power supply (Fig.18)
▪ Remove the upper section of the vacuum cleaner. Fit
either the supplied pleated polyester filter onto the
basket and screw the locking cap to close the filter
basket (Fig.19a); or fit the dust bag flange onto the in-
let stub (Fig.19b). Take care not to damage the dust
bag.
▪ Place the upper section back on the tank and clip the
clamps (Fig.20).
▪ Insert the larger end of the hose into the tank front
inlet and lock in place. Choose the appropriate nozzle
or metal tube and install them onto the hose free end
(Fig.21).
▪ Plug in the vacuum cleaner (Fig.22).
▪ Place the switch (12) to position "I" to switch the motor
on (Fig.23). Push the automatic mode switch (10) to
position "–" (Fig. 24).
▪ When you have completed vacuuming, switch the
motor off by shifting the switch (12) to position "O" and
unplug the cable.
5
EN