Maintenance And Service - Bosch GKF 550 Professional Notice Originale

Affleureuse

Masquer les pouces Voir aussi pour GKF 550 Professional:

Notice originale (179 pages)

Notice d'utilisation d'origine (171 pages)

Notice originale (179 pages)

Table Des Matières

Table des Matières

Les langues disponibles

Starting Operation

Switching on/off

To switch on the power tool, set the on/off switch (11) to I.

To switch off the power tool, set the on/off switch (11) to 0.

Working Advice

Protect router bits against shock and impact.

Pull the plug out of the socket before carrying out any

work on the power tool.

Routing direction and routing process (see figure D)

Routing must always be carried out with the work-

piece being moved against the direction in which the

router bit (6) is turning (up cut). If the workpiece is

moved in the same direction as the router bit is turning

(down cut), the power tool may be pulled out of your

hands.

Only use the power tool when the routing base (2) is

fitted. Losing control of the power tool can cause injur-

ies.

Note: Be aware that the router bit (6) always protrudes

slightly from the base plate (9). Do not damage the template

or the workpiece.

Set the routing depth you want.

Switch on the power tool and guide it to the point you want

to machine.

Switch off the power tool after routing.

Do not put the power tool down before the router bit

has come to a complete stop. Application tools that are

still running can cause injuries.

Routing with guide bushing (see figure E1 – E3)

Using the guide bushing (17), you can transfer contours

from templates or patterns to the workpiece.

Select the guide bushing that is suitable for the thickness of

the template or pattern. Due to the protruding height of the

guide bushing, the template must have a minimum thickness

of 8 mm (see figure E1).

Select a router bit with a diameter that is smaller than

the interior diameter of the guide bushing.

Unscrew the four cylinder screws on the underside of the

guide plate (8) and remove the guide plate.

Insert the guide bushing (17) into the guide plate (see fig-

ure E2).

Loosely screw the guide plate back onto the base plate (9).

It must still be possible to move the guide plate freely.

To ensure that the distance between the centre of the router

bit and the edge of the guide bushing is uniform, the guide

bushing and guide plate must (if necessary) be centrally

aligned with each other.

– Align the guide plate such that the router bit and guide

bushing are centred on the opening in the guide plate

(see figure E3).

– Hold the guide plate in this position and firmly tighten the

fastening screw.

Bosch Power Tools

To rout with the guide bushing (17), proceed as follows:

– Place the power tool with the guide bushing (17) onto the

template.

– Guide the power tool with the protruding guide bushing

along the template using lateral pressure.

Edge or profile routing (see figure F)

For edge and profile routing without a parallel guide, the

router bit must be fitted with a pilot pin or a ball bearing.

While it is switched on, guide the power tool towards the

workpiece from the side until the pilot pin or the ball bearing

of the router bit is touching the side of the workpiece edge

that you want to machine.

Guide the power tool along the workpiece edge. Pay atten-

tion that the router is positioned perpendicularly. Too much

pressure can damage the edge of the workpiece.

Routing with a parallel guide (see figure G)

You can fit a parallel guide (18) for when cutting parallel to

an edge.

Fit the parallel guide (18) to the routing base (2) using the

knurled screw (4).

Set the required stop depth using the wing bolt on the paral-

lel guide (19).

While it is switched on, guide the power tool along the work-

piece edge with a uniform feed and while applying lateral

pressure to the parallel guide.

Routing with a pilot (see figure H)

The pilot (20) helps when routing edges with router bits

without a pilot pin or ball bearing.

Fit the pilot to the routing base (2) using the nut (4).

Guide the power tool along the workpiece edge with a uni-

form feed.

Lateral clearance: To change the amount of material being

removed, you can adjust the lateral clearance between the

workpiece and the guide roller (23) on the pilot (20).

Loosen the wing bolt (21), set the lateral clearance you want

by turning the wing bolt (22), then retighten the wing

bolt (21).

Height: Set the vertical alignment of the pilot according to

the router bit you are using and the thickness of the work-

piece you want to machine.

Loosen the nut (4) on the pilot, slide the pilot into the de-

sired position and retighten the bolt.