EINHELL RUBIN Instructions De Montage page 7

Page 45
30/p: Slide a DT latch (item 2) into each of the guide
rails of the door closing profiles (item 5). In addition,
fasten a hex screw to each end approx. 5 cm from
the edge.
Page 46
30/s: Fasten three hinge blades to one of the side
door profiles (item 6). Make sure that the hinge
blades are inserted in the way shown in the profile
diagram.
Page 47
30/u: Fit one of the striker plates to the middle of the
profile and the other approx. 65 cm from the top
edge. Make sure that the striker plates are fitted in
the way shown in the profile diagram.
Page 48
30/v + 30/w: Attach the door profile with the hinge
blades to the right-hand side of the middle door
profile (refer to step 30/s). On the left-hand side,
attach the door profile to the striker plates (refer to
step 30/u).
Page 51
31
Assembly of the double door
31/a: Attach the two right-hand door wings to the
door pivot profile with the four pre-assembled hinges.
Page 52
Note (Figure 31/c): During assembly of the door
wing stop (art. no. 84.080.41), make sure that the
upper door wing is opened further than the lower.
Page 53
31/d: Attach the two left-hand door wings to the door
pivot profile with the three pre-assembled hinges.
Page 55
Figure 31/h: External view of the lower part of the door
31/h: Before you fit the two door stays, open the two
door wings and mark on the door profile the positions
at which the clip stops against the door. Fit the door
stays at these points (Art. No. 57.013.32).
31/i: Now align the striker plates which have already
been pre-assembled on the door hinge. The lower
striker plate on the long door wing is aligned so that
the latch can be pushed into the ear. The two upper
striker plates should be at the same level to allow
a padlock (not included with the greenhouse)
to be attached.
ABA_RUBIN_Teil2_Titel+GB.pmd 7
Page 56
31/j: The DT latch mounted on the right-hand upper
door wing joins the two halves of the door.
Rotate the DT latch through 90 degrees until it
clamps the rabbet profile on the lower door wing.
31/k: The left half of the door can be fastened with
the help of the two latches attached to the long
door wing.
Page 57
32
Pre-assembly of the window
Important note: The step below describes the
method for assembling a single window. Repeat this
step for the second and third window.
Page 59
Important note: The outside of the plastic web
panels (with UV coating) is marked „Außenseite /
Outside" at the edge, and it is also the side onto
which the protective film has been stuck. Only
remove the protective film from the plastic web panel
you are currently installing.
Page 60
32/f: Cut two 646 mm lengths from the window
sealing profile and slide them into the designated
guide rails on the side profiles of the window (refer to
the profile diagram).
Important note: Once you have pulled in the window
sealing profile, slightly pinch the guide profile at the
lower end so that the rubber cannot slip out of the
profile.
Page 61
33
Assembly of the window
Important note: Repeat this step for the second
and third window.
33/a: Slide a window stopper from the front into the
corresponding guide rail in the ridge profile as shown
in the illustration and insert it as far as the second
roof strut.
33/b: Then slide the window into the same guide rail
(refer to the profile diagram). Secure the window by
sliding in the second window stopper up to the
window.
Important note: Make sure that the window is
positioned exactly between the roof struts so that a
perfect fit is ensured when closing the window.
07.04.2006, 09:48
7