Door Swing Dimensions; Custom Side Panels - Jenn-Air Euro-Style Design JS42SSDUDE Guide D'installation

Réfrigérateur encastré côte à côte
Masquer les pouces Voir aussi pour Euro-Style Design JS42SSDUDE:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Top View
Model
A
42 Euro-Style
41" (104.1 cm)
48 Euro-Style
47" (119.4 cm)
®
42 Pro- Style
41" (104.1 cm)
®
48 Pro- Style
47" (119.4 cm)
Front View
Width dimensions were measured from trim edge to trim edge.
Height dimensions are shown with leveling legs extended
¹⁄₈" (3 mm) below the rollers.
A
(see chart following)
Model
Width A (Trim edge to trim edge)
42
42¹¹⁄₃₂" (107.5 cm)
48
48¹¹⁄₃₂" (122.8 cm)
*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below
rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

Door Swing Dimensions

The location must permit both doors to open to a minimum of 90°.
Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the
refrigerator and a corner wall.
8
A
³⁄₈
25
"
(64.5 cm)
B
B
2¹⁄₈" (5.3 cm)
2¹⁄₈" (5.3 cm)
2⁵/₈" (6.67 cm)
2⁵/₈" (6.67 cm)
³⁄₈
*83
"
(211.8 cm)
NOTE: More clearance may be required if you are using overlay
panels, custom handles, or extended handles.
To adjust the door swing, see "Adjust Doors."
42" (106.7 cm) Models
¹⁄₄
37
"
(94.6 cm)
A
³⁄₈
41
"
(105.1 cm)
90˚
110˚
130˚
Model
A
®
Pro-Style
10³/₄" (27.11 cm)
Euro
10¹/₄" (25.87 cm)
48" (121.9 cm) Models
39"
(99.1 cm)
A
⁷⁄₈
43
"
(111.4 cm)
90˚
110˚
130˚
Model
A
Pro-Style
®
12³/₁₆" (30.84 cm)
Euro
11⁵/₈" (29.43 cm)

Custom Side Panels

Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or when
the refrigerator is placed at the end of a cabinet run.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type
of installation you are planning.
NOTES:
The dimensions shown are actual product dimensions and
may not reflect the needed panel installation dimensions.
The side panel should be a minimum of ½" (1.27 cm) thick
to avoid warping.
If the opening depth is 25" (63.5 cm) or more, you may want
to install a support board on rear wall.
¹⁄₂
41
"
(105.4 cm)
B
47
(121.6 cm)
90˚
110˚
130˚
B
14¹/₄" (36.11 cm)
13³/₄" (34.88 cm)
44"
(111.8 cm)
B
51
(130.5 cm)
90˚
110˚
130˚
B
16¹/₄" (41.16 cm)
15¹¹/₁₆" (39.75 cm)
⁷⁄₈
"
³⁄₈
"

Publicité

Table des Matières
loading

Table des Matières