Easy, 3-Step Installation; Standard Bike Rack Mounting; Seat Pad Installation; Foot Rest Installation - Bell SUPER SHELL Mode D'emploi

EASY, 3-STEP INSTALLATION

ATTACH MOUNT ONTO BIKE FRAME
1
1. Remove four (4) screws from back of
mount using 5mm Allen wrench.
2. Place front of mount around seat
tube of bike. Insert back of mount
to front of mount, insert screws.
Do not fully tighten. Do not place
around brake and derailleur cable
and housing.
CLICK RACK INTO MOUNT
2
1. Slide the ends of the carrier rack into the top holes on the mount.
Once secured, you will hear a click. This means the carrier rack is
secured to the mount.
2. Slide the loose mount up or down until there is about 6"
between rear wheel and bottom of carrier. Be sure mount is
centered along rear wheel facing forward.
3. Tighten the screws on the mount until mount will not slip
up, down, or side to side.
4. Tighten fasteners securely, and check them frequently.
CARRIER RACK ATTACHMENT
3
1. Insert carrier rack bars simultaneously into bicycle mount. You should hear a
"click" when properly secured.
CHILD CARRIER ATTACHMENT
1. Untwist the clamp on the bottom of the child carrier by
turning the knob.
2. Place carrier clamp over the carrier rack, hook one
side of the clamp around the edge, then push the
other side of clamp down over carrier rack and turn
knob to tighten the clamp around the carrier rack.
The knob has a security feature so that it does
not loosen accidentally. To tighten or loosen
the clamp, pull the knob handle out, and
at the same time, turn to tighten or
loosen accordingly.
3. Loop security strap webbing
around seat post.
CHILD CARRIER REMOVAL
1. Unclip the security strap.
2. Pull knob out and twist until carrier
clamp loosens the seat.
WARNING
Hearing a clicking sound does not mean the knob is tight. You must pull knob
out and twist until secure.
WARNING
Do not modify child carrier or bicycle. If carrier rack will not fit on your bicycle, consult your local bicycle dealer or call our Customer Service
1.800.456.BELL for assistance. Failure to properly attach clamp onto the carrier rack could result in the child carrier falling off the carrier rack.
4 | English

STANDARD BIKE RACK MOUNTING

The Super Shell can be secured to and removed from most
standard bicycle racks by following the steps in the Seat
Attachment and Seat Removal sections. The mount and carrier
rack included do not need to be installed for this configuration.
WARNING
A standard bicycle rack must have a load rating of 40 pounds
or greater to be used with the child carrier. Failure to properly
attach clamp onto the carrier rack could result in seat falling off
the carrier rack.

SEAT PAD INSTALLATION

Place seat pad into bottom of child carrier. Thread retention
harness through seat pad. Insert all four seat pad plugs into the
bottom of the child carrier.

FOOT REST INSTALLATION

To insert foot rest, insert top hook into preferred height. Slide
bottom tab into slot and pinch both together at the same time
while pushing the foot rest into place. Pull at them gently to
ensure they are secured properly. To remove foot rest, pinch
the hook and tab at the same time and pull up, freeing the
bottom tab. Then pull the top hook free.

FOOT STRAP ATTACHMENT

1. Loop one piece of Velcro through each foot rest and attach
®
back onto itself.
2. Insert top hooks of foot rests into opening along leg. Must be
at least three notches from bottom. Push to lower tabs
through respective opening and click into place. Lower hook
tabs need to be lifted slightly when inserted into slot.

OSCILLATING GRAB BAR

While riding, the grab bar can be used in either the forward or
back locking positions. Push both round buttons on each side
of bars to pivot front or back until it clicks into place.

CHILD CARRIER ADJUSTMENT

Child carrier should be positioned as far forward as practical.
WARNING
Positioning the child carrier too far back will increase the risk of
loss of steering and/or braking control.

SEATING YOUR CHILD

WITH ONE PERSON HOLDING THE BICYCLE STEADY, THE
SECOND PERSON PLACES CHILD IN CHILD CARRIER.
Adjust harness to child's height. If child's shoulders are at or
below the lower strap slot holes, move the harness to the lower
holes. Push the plastic washer that hold the ends of the harness
out through the holes. Fasten buckles accordingly.
5 | English