Publicité
Les langues disponibles
Les langues disponibles
With the purchase of an Aqua Medic cooling unit, you have selected a top quality product. It has been specifically
designed for the cooling and heating of closed water cycles like fresh and salt water aquaria. The TITAN
Professional units are supplied with heat exchanger made from saltwater proof Titanium steel. These heat
exchangers are corrosion-resistant and free of contaminations. The Titan Professional units can be used in fresh
water and salt water as well as in various chemicals.
1.
Features
The units of the Titan Professional line are automatic machines to control and adjust the water temperature.
They work as heat pumps and switch automatically between heating and cooling to keep the water temperature
in the desired range. The main application will be for cooling down the aquarium water. But they are also very
effective heaters. The Titan 6000 Professional has a heating capacity of 5,200 watts with only 1,400 watts of
power uptake.
2.
Set-up and installation
1. The cooling unit must be set up at a well-aerated place. The complete heat taken out of the water by
the unit and the waste heat of the unit itself are emitted at the unit to the surrounding air. A build-up of heat
directly at the cooling unit leads to a heavily reduced cooling power output. Therefore, sufficient ventilation
is essential.
The environmental temperature should not exceed 35 °C.
2. The cooling unit has to be connected to a closed water cycle. It is recommended to place the unit below the
water surface (max. 2 m below).
3. Switch the water flow on. It is important that the water flows continuously through the cooler.
Because the temperature-sensor is placed within the unit, the heat exchanger cannot freeze in case of a
failure of water supply.
4. Before starting, the cooler should stand up straight for at least 1 hour. Connect it to 230 V power source and
switch the unit on (plug in the mains and switch on). Now, the actual water temperature is shown on the
display. Because the thermo sensor is placed in the water inlet, always a temperature which corresponds to
the temperature in the tank is shown.
3.
Technical Data
Modell
Power supply:
Cooling capacity (W):
Heating capacity (W):
Compressor power (HP):
Power uptake „cooling":
Power uptake „heating":
Rated current consumption (A):
Recommended flow rate (l/h):
Max. aquaria's volume:
ΔT = 5 °C
ΔT = 10 °C
Cooling
agent
and
Heat exchanger:
Diameter of water inlet and outlet: 1,5" / D 50 mm
Ambient temperature:
Temperature control range:
Max. water pressure:
Factory settings:
Dimensions l x w x h (mm):
Net weight (kg):
8
Operation Manual ENG
Titan
Professional
4.000
220 – 240 V~/50
Hz
3,800
3,800
1.5
1.25
1.08
6.5
3,000-10,000
4,000 l
2,000 l
cooling R410A/1,180 g
Titanium
5 °C – 38 °C
5 °C – 36 °C
740x410x740
73
Titan
Titan
Professional
Professional
6.000
8.000
220 – 240 V~/50 Hz
5,200
7,200
5,200
7,200
2
3
1.78
2.34
1.40
1.75
9.8
12.5
4,000–12,000
6,500–16,000
6,000 l
8,000 l
3,000 l
4,000 l
R410A/1,080 g
R410A/1,300 g R410A/ 2,400 g
Titanium
1,5" / D 50 mm
5 °C – 38 °C
5 °C – 36 °C
0.2 bar
setpoint 20 °C, switching hysteresis 1 °C
740x410x740
750x460x750
68
78
Titan
Professional
15.000
380 V ~, 3
Ph./50 Hz
14,900
14,900
5
3.95
2.90
20.8
10,000–32,000
15,000 l
7,500 l
850x550x980
150
Publicité
