Vacation And Moving Care - KitchenAid W10136157B Guide D'utilisation Et D'entretien

NOTE: Make sure the plastic spacer from the right-hand side
of the cutter grid bracket stays with the cutter grid.
A
B
C
A. Cutter grid harness
B. Screw
C. Cutter grid
8. Remove the two thumb screws that hold the water pan in
place. Push down with one hand on the front of the pan while
pulling forward on the bottom back side.
B
A. Water pan
B. Water pan thumb screws
C. Drain cap
9. Remove, clean and replace the ice scoop and ice scoop
holder.
After removing the ice scoop, remove the holder by lifting
the front free from the cutter grid cover. Then lift the back
of the holder slightly to release the rear hook and pull
forward.
Wash the ice scoop holder along with the other interior
components using the following instructions.
Replace the ice scoop holder by aligning the rear hook
with the opening (the holder angles down slightly). Slide
the holder back fully until the front rests securely on the
cutter grid cover.
A. Ice scoop holder
10. Wash the interior components (cutter grid, exterior of hoses,
and water pan) and the storage bin, door gasket, ice scoop,
and ice scoop holder with mild soap or detergent and warm
water. Rinse in clean water. Then clean the same parts with a
solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L)
warm water. Rinse again thoroughly in clean water.
NOTE: Do not remove hoses. Do not wash plastic parts in
dishwasher. They cannot withstand temperatures above
145°F (63°C).
11. Replace water pan by pushing back on the bottom with one
hand while pushing up and back on the top. Secure the water
pan by replacing both screws.
D
E
F
D. Ice level sensor harness
E. Plastic spacer
F. Screw
A
B
C
A
12. Check the following:
Drain cap from the water pan is securely in place. If the
drain cap is loose, water will empty from the water pan,
and you will have either thin ice or no ice.
Hose from water pan is inserted into storage bin drain
opening.
13. Slide the cutter grid back into place and secure it by
replacing the right-hand screw and plastic spacer. Then
tighten the left-hand screw. Reconnect the cutter grid
harness and the ice level sensor harness.
14. Replace the cutter grid cover.
15. Plug in ice maker or reconnect power.

Vacation and Moving Care

WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
To shut down the ice maker:
1. Unplug ice maker or disconnect power.
2. Remove all ice from storage bin.
3. Shut off the water supply.
4. Remove the two screws in the lower access panel and the
two screws from the base grille area of the front panel
support. Pull forward to remove the lower access panel.
A
B
A. Lower access panel screws
B. Base grille screws
5. Disconnect the inlet and outlet lines to water valve. Allow
these lines to drain and then reconnect to the valve.
6. Replace lower access panel and screws.
7. Drain water from water pan by removing the drain cap.
8. If the room temperature will drop below 32°F (0°C), water
must be removed from the drain line.
For ice makers with a drain pump installed:
Plug in ice maker or reconnect power.
Turn ice maker off and remove all remaining ice from ice
bin.
Pour 1 qt (0.95 L) of water into the ice bin near the drain
and let the unit stand for approximately five minutes. This
will allow the water in the bin to drain into the drain pump
so that the pump will remove the remaining water from
the ice bin and the drain pump.
Unplug ice maker or disconnect power.
A
B
9