TDK-Lambda FPS1000 Série Mode D'emploi page 21

FPS1000 INSTRUCTION MANUAL
FPS1000 SERIES SPECIFICATIONS
1 Rated output voltage
2 Output voltage set point
3
Output voltage range
4 Maximum Output Current (Refer to Fig.1)
5 Maximum output power
6 Input voltage / frequency range
7 Maximum input current (at 100/200Vac)
8 Power Factor (Typ)
9 Efficiency (Typ)
10 Inrush current
11
Hold-up time
12 Maximum line regulation
13 Max load regulation
14 Output Ripple and noise pk-pk
15 Temperature stability
16 Temperature coefficient
17 Remote sensing
18 Parallel operation
19 Series operation
20 Over current protection
21 Over voltage protection
22 Over temperature protection
23 Remote On/Off control
24 DC OK signal
25 Over-Temp. warning
26 AC fail signal
27 Auxiliary power supply
28 Vout voltage trimming
29 Front panel indicators
30 2
I C Interface
31 Operating temperature-models without IEC inlet
models with IEC inlet
32 Storage temperature
33 Operating humidity
34 Storage humidity
35 Cooling
36
Vibration
37 Shock
38 Conducted emission
39 Radiated emission
40 Applicable safety standards
Withstand voltage
41
42 Isolation resistance
43 Leakage current
44 Weight (Typ)
45 Size (W*H*D)
Notes:
*1: For cases where conformance to various safety standards (UL, EN etc.) is required,
to be described as 100-240Vac (50/60Hz).
*2: At 100/200Vac, rated load and 25˚ C ambient temperature.
*3: Not applicable for the noise filter inrush current less than 0.2mS.
*4: Measured with JEITA RC-9131A 1:1 probe, 20MHz B.W.
*5: From 85~132Vac or 170~265Vac, constant load.
*6: From No-load to Rated load, constant input voltage. Measured at the sensing point in Remote sense.
*7: Remote sensing can compensate up to 1V drop on each load wire.
*8: Inverter shut down method. Reset by AC voltage recycle or by On/Off control.
*9: Derate Maximum output power by 10% for input voltage less than 100V
*10 For FPS 1000-12/P(S), when used not with FPS-S1U or FPS-T1U
racks, an EMI suppressor clamp should be attached to the AC cable,
as close as possible to the AC inlet, to meet class B.
Model FPS1000
V/I -12
V1 (V) 12
V2 (V) 13.2
I1 (A) 66
I2 (A) 72
FPS1000-12
V
V 12+/-1%
V 10.5~13.2
A
W
(*1) ---
A
---
(*2) %
(*3) A
mS 20mS typical at 100Vac input, rated output voltage and less than 80% of rated load.
(*5) ---
(*6) ---
(*4) mV
--- 0.05% of rated Vout for 8hrs after 30min warm-up. Constant line, load and temperature.
PPM/°C
(*7) V
(*9) ---
---
---
(*8) V 14.3~15.7
---
--- By electrical signal or dry contact. ON: 0~0.6V or short. OFF: 2~15V or open.
--- Open collector signal. On when Vout ≥ 80+/-5% rated output. Max.sink current: 10mA
---
---
---
---
---
---
--- 0~50°C: 100% load. Derate 2%/°C, 50°C to 60°C, Derate 2.5%/°C, 60°C to 70°C.
---
---
---
---
---
---
---
---
(*10)
---
---
Input-Output: 3000Vrms, 1min. Input-Ground:
---
---
mA
Kg
---
FPS1000 FPS1000 FPS1000
-24 -32 -48
24 32 48
29 38.4 58
33 26 17.25
40 31 21
FPS1000-24
12 24
24+/-1%
21.5~29
72 40
864 960
85~265Vac continuous, 47~63Hz, Single phase
>0.98 at 115/230V and maximum output power
81/83% 84/86%
Less than 40A
150 200
Possible. Refer to Instruction Manual.
Possible. Refer to Instruction Manual.
Possible. Refer to Instruction Manual.
104%~125% of maximum output current. Refer to Fig. 1
31~34
Inverter shut down method, automatic reset.
Open collector signal. Refer to Instruction Manual
Open collector signal. Refer to Instruction Manual
11.2~12.5VDC. 0.25A Maximum output current.
Possible, via Vout Trim pin in the I/O connector. Refer to Instruction Manual.
AC OK, DC OK, DC FAIL
Optional. Refer to Instruction Manual.
0~50°C: 100% load. Derate 2%/°C, 50°C to 60°C.
10~90% RH, no condensation.
10~95% RH, no condensation.
By internal Fans. Variable speed control.
Built to meet ETS 300 019
Built to meet ETS 300 019
Built to meet EN55032B, FCC part 15J-B, VCCI-B
Built to meet EN55032B, FCC part 15J-B, VCCI-B
IEC 62368-1 UL62368-1 CSA22.2 No.62368-1 EN62368-1.
More than 100Mohm at 25°C and 70% RH. Output-Ground: 500Vdc
Less Than 1.1mA at 230Vac
127x41x290mm. Refer to Outline Drawing.
.
RMS
Vout (V)
V2
V1
Fig. 1: Rated output current vs output voltage
FPS1000-32 FPS1000-48
32
32+/-1% 48+/-1%
28.8~38.4
31
992
12.0/6.0
84/86% 85/88%
0.40%
0.80%
250
200
41.5~45.5
-30~85°C
Vrms, 1min. Output-Ground: 500Vrms,1min.
2000
2.0
I2
I1
48
43~58
21
1008
300
62~66
Iout (A)
21