Peg-Perego book Notice D'emploi page 17

17• ADJUSTING THE FOOTREST: the footrest
can be adjusted to 2 positions. To lower
the footrest, push the two little side levers
downwards and lower the footrest at the
same time. To raise the footrest, push it
upwards until it clicks.
1 8• ADJUSTING THE BACKREST: the backrest
can be reclined into 8 positions. To lower
the backrest, lift the handle and lower the
backrest at the same time. Block it in the
desired position. To raise the backrest, lift the
handle and raise the backrest at the same
time. Block it in the desired position.
19• FRONT BUMPER BAR: to attach the front
bumper bar remove the protection caps
(Fig.a) and store them.
After removing the caps, insert the ends of
the bumper into the armrests until they click
(Fig.b).
20•The bumper bar can be opened on one side so
an older child can climb on and off more easily.
To open the bumper bar, push the button on
the side and pull the bar outwards (Fig.a)
To remove the bumper bar, press the
two buttons on the sides and pull the bar
outwards (Fig.b).
When the bumper bar is off, replace the
protection caps onto the chassis armrests to
close them.
21• COLLAPSING THE STROLLER: to collapse
the stroller, put the front wheels into fixed
position, close the hood and remove the car
seat (if on the chassis).
- Align the handle with the stroller chassis as
shown in the picture (fig_a);
- lift the fastening hooks on the two sides of
the chassis (fig_b);
- Pull the interior handle placed behind the
seat (fig_c) and lift at the same time (fig_d).
22• Rotate the handle forward until completely
closed (fig_e).
Check that it has fastened to the closing hook
on both sides. If it has not, fasten the closing
hook properly as shown (fig_f).
The collapsed stroller is free standing.
23•To make the stroller smaller still, the back wheels
can be removed. Pull the pivot outwards and
extract the wheel as shown (fig_a).
TRANSPORT: the stroller can be carried
comfortably locking the front wheels and
grasping the main handle (fig_b).
2 4• REMOVING THE LINING: to remove the
stroller's lining:
- unthread the belt's leg divider from under the
seat (fig_a);
- slip the elastics off their hooks on both sides
(fig_b);
2 5• - unscrew the belt on both sides, keeping
your finger under the bolt (fig_c);
- unfasten the lining from the armrests as
shown in the picture (fig_d);
- lift the flaps and release them from the velcro
fabric to unbutton the seat's lining (fig_e);
26• - on the back of the pushchair:
- remove the lining from the seat (fig_f);
- with the help of a screwdriver, remove the
elastic from its groove (fig_g);
- undo the buttons on both sides on the
backrest (fig_h);
27• Use the screwdriver to remove the screw in
the main handle, on both sides (fig_i);
- Store the screw after removing it.
- Unthread the strap from the lining (fig_l);
28• Unfasten and remove the shoulder straps
from the backrest as shown in the figure 15_a
/ 15_b;
- push in the openings and pull off the side
lining.
Do this on both sides (fig_m);
- Unfasten the canopy from both sides of the
stroller's backrest (Fig.10 c) and on the inside
of the handlebar (Fig.10 d).
- remove the lining from above (fig_n).
REPLACING THE LINING: to put the lining back on:
- fit the lining onto the backrest
- fit the lining over the platform
- attach the side elastics (24b)
- fasten the lining's hooks to the armrests (25d)
- fasten the lining's buttons to the chassis and
lower the velcro straps (25e)
- fasten the belt in the right position with the
screwdriver (25c)
- attach the leg divider under the seat. One part
must be above the seat and one below (24a)
- attach the belt at the desired height (point 15)
29• on the back of the stroller:
- insert the two rigid flaps between the tube
and the seat (fig_a);
- thread the strap through the lining's eyelet.
Replace the main handle's screw (fig_b).
WARNING: stretch the strap to check it is
securely fastened.
- Button the lining onto the stroller's backrest
(26h).
- 17 -