Maintenance And Cleaning - Novellini R90 Notice D'utilisation, D'installation Et D'entretien

PRODUCT GUARANTEE:
The product is guaranteed as per Italian Presidential Decree
224 of 24/05/1988 in Italy and the rest of the EU and as per
CEE Directive 85/374 in terms of product liability.
The Manufacturer guarantees its
manufacturing and material defects – provided these are
confirmed by the authorised personnel of the Company – for
a period of 24 months from the purchase date, as indicated
by the receipt or invoice.
The guarantee covers repairs to and/or replacement of the
parts considered to be faulty. The guarantee does not cover
complete replacement of the product. The guarantee does
not cover the lights, warning lights, fuses, glass parts, mirrors
and decoration parts unless these are faulty due to production
defects and not due to neglect or improper use. The
guarantee does not cover any parts and components which
are faulty or damaged due to negligence or carelessness
during use, incorrect installation or maintenance, operations
carried out by non-authorised personnel, damage caused
during transport or any other circumstances not due to
product manufacturing defects, such as sudden electricity
jolts, lightning, electrolysis, corrosion and, in general, any
causes related to the nature of the water and electrical and
water supply systems in the place where the unit is used.
The Purchaser must check that the product is not damaged
in any way before installation and must contact the agent
or authorised assistance centre immediately if any faults are
detected. The guarantee will only be applied on presentation
of a document indicating the purchase date.
In the event of operations without proven defects or to
illustrate how to use the product, all the expenses are
sustained by the Purchaser. Any repairs or modifications
carried out by personnel not authorised by the Manufacturer
will not be covered by the guarantee and will render the
remaining guarantee period immediately null and void.
The Manufacturer is not responsible in any way for any direct
or indirect damage caused to persons, animals or things due
to failure to comply with all the regulations in the installation,
instruction and maintenance manual supplied with the
product.
Any disputes will be dealt with exclusively by Mantova Italy,
Law Court.
This symbol indicates important product instructions
or important safety information.
IMPORTANT:
Before you start to assemble and install the product, carefully
read through all the instructions. Unpack the components
and check that nothing is missing and that there are no
damaged or faulty components, remove the transparent
protective film. Before you install the shower cubicle in its
final position, perform a test run. Run the unit for several
minutes and check for water leaks and any damage caused
during transport and handling. This product should be
installed by suitably skilled personnel.
N.B.: This product is designed for installation on finished walls
and floors.
Warranty claims must be produced with the purchase invoice
and the product assembling instructions.
The drawings and illustrations in this manual are provided for
information purposes only.
The manufacturer reserves the right to make changes and
improvements without prior notice.
Electrical connection:
The manufacturer certifies that the product conforms to
current health and safety regulations at the time of sale
and that the product has the CE-mark and Declaration of
Conformity. All products and components are tested during
manufacture in accordance with the relevant reference
standards and company quality system procedures. In order
to ensure that your manufacturer product maintains these
high standards after installation and throughout its service
life, please read the following instructions.
1. Check that the mains electrical equipment connected
to cubicle conforms to current electrical standards and
regulations and is fitted with a fully efficient earth connection.
2. Current electrical regulations forbid the installation of any
electrical equipment (e.g. plugs, switches) inside a radius of
60 cm from the cubicle and at a height of 225 cm.
3. Check that rating of the mains power supply line matches
the absorbed power specified for the cubicle (see Technical
specifications, page 5).
4. The electrical connection between the cubicle and the
mains must be protected against water spray and must have
a protection rating of IP55 or higher.
5. The electrical equipment upstream from the cubicle must
be fitted with an omnipolare 30 mA switched circuit breaker
with a minimum contact opening of 3 mm, which conforms
to current electrical regulations
6. The manufacturer declines all responsibility for injury or
damage resulting from failure to observe these instructions.
products against
~
STEAM:
Once power is turned on, the display shows:
ADJUST TIME:
Time can be adjusted in stand-by only.
Hold down the
Press and
Press to confirm and go on to the minutes. Press
to adjust.
Press to confirm. The time is set.
LOCATING AND MEMORISING THE RADIO:
1) Press to turn the radio on. Use buttons
adjust the volume.
2) Press (Mhz flashes) to locate the frequency required
600 mm
1
2400 mm
2
3
(I)
button for a few seconds, the hours flash.
to adjust.
and
-29-
by moving with the and
memorise.
Press to go from M0 to M9 to change the stations
memorised.
Repeat these steps to locate and memorise other channels.
SETTING THE SAUNA:
The length of the sauna must be set before starting the sauna
cycle (stand-by).
Press . The length of the sauna shows on the display.
Press and to set the length of the sauna from a
minimum of 5 minutes to a maximum of 40. The value set will
be proposed again the next time you use the sauna.
Press to start the sauna. After about 8 minutes, the system
emits a beep to indicate that the sauna is at temperature and
you can enter the cubicle.
During the sauna you can set the required climate.
When is pressed, the climate indicators flash.
Use the and buttons to select a minimum, medium
or maximum climate.
After a few seconds from selection, the climate indicators
stop flashing and the climate selected is set.
After the set time, the system emits a beep to indicate the
sauna is over.
and
ALARM:
In case of necessity, the alarm button
at any time. When pressed, the heat generator goes off
immediately together with all other functions, activating a
warning signal (after 15 minutes it goes off automatically).
To deactivate it before, just press any other button.

MAINTENANCE AND CLEANING:

After 20 saunas, the symbol
indicating that a cleaning cycle is required.
You should also perform a cleaning cycle if the sauna is not
used for a long period.
to
IMPORTANT!
During cleaning, it is absolutely prohibited to remain
inside the cubicle.
Remove the cover from the diffuser and aroma container.
To activate the cleaning cycle, in stand-by, hold the
button down for about 8 seconds until the
appears on the display. During the cleaning cycle, the 2 LEDs
ENGLISH
buttons. Press to
may be pressed
appears on the display
symbol