Set Up The Parent Unit; Check The Connection; Using The Baby Monitor; Adjust Volume - Brevi 381 Notice D'emploi

ISTRUZIONI DIGITAL BABY MONITOR 381:ISTRUZIONI DIGITAL BABY MONITOR 381
GB
WARNING! Do not use common batteries, but use rechargeable batteries only.
Rechargeable batteries must be set up by respecting the polarity. Do not mix new and used rechargeable
batteries. Do not mix rechargeable batteries types. Use only rechargeable batteries of the
recommended type or similar type. Do not short-circuit battery terminals. Rechargeable batteries
should only be changed under adult supervision.

2. SET UP THE PARENT UNIT

2.1 Power supply
The parent unit uses either two AAA rechargeable batteries (picture 10)
Battery operations
a) Remove the battery compartment cover and insert 2 x AAA rechargeable batteries into the battery
compartment on the parent unit and replace the battery compartment cover as shown.
You should always ensure you have inserted batteries in the parent unit (pictureS 16a-16b-16c)
WARNING: Never use non-rechargeable batteries in your parent unit.
Use only the recommended type 2 x AAA rechargeable batteries – using other types
could permanently damage your unit (pictures 7a-7b).
b) Plug the charger for the parent unit into the main power socket (pictures 11a-11b)
WARNING: Use only the main power adapter supplied. Using an incorrect adapter may
permanently damage the charger.
c) Slot the parent unit into the charger (picture 11c); the charger light will stay red, even when batteries
are fully charged (picture 11d)
d) Push the button "ON-OFF" (picture 11e); the "Power" led and "Link" led will turn on. 11f)
NOTE 1: charge the parent unit for at least 8 hours before using the baby monitor for the first time
2: battery insertion or replacement is necessary if an unlit charger light
3: charging or battery replacement is necessary if the following occurs:
• The power indicator LED does not light.
• Battery low: The power indicator LED blinks (picture 11h)
4: the Parent Unit can still be used when it is in the charger.
5: Please power off the Parent Unit before removing the batteries.
WARNING! Batteries should not be recharged. Batteries or rechargeable batteries must be set up by
respecting the polarity. Do not mix new and used batteries or rechargeable batteries. Do not mix
battery types. Use only batteries or rechargeable batteries of the recommended type or similar type.
Remove used batteries or rechargeable batteries from the product. Do not short-circuit battery ter-
minals. Rechargeable batteries must be removed from the product before charging wherever pos-
sible. Rechargeable batteries should only be changed under adult supervision.
26
19-06-2008 10:19 Pagina 27
2.2 Belt clip
For added convenience, use the belt clip (picture 12)

3. CHECK THE CONNECTION

When both units are switched on, the link lights on both units will turn green (picture 13a).
If the link between the units is broken at any time, the link lights on both units will turn red.
At the parent unit, you will also hear an alert signal to warn you that there is no communication
between the units. If this happens, check that the mains power is plugged in and switched on at the
baby unit (picture 13b).
Also check that the Units are within range of one another.
NOTE In the event of power failure, when the power is restored all your settings will remain unchanged.

USING THE BABY MONITOR

Position both units in the same room to test the connection. Make sure the baby unit is at least 1 meter /3
feet away from the parent unit (picture 13a).
NOTE If you place the parent and baby units too close together you will hear a high pitched noise, this
is normal. The units are designed to be located at a distance from one an other, e.g. in different
rooms (picture 13b).
4. USING THE BABY MONITOR

4.1 Adjust volume

At the parent or baby unit:
• There are 6 volume levels on each unit.
• Press + to increase or
affects the volume when you use the talk back feature (picture 14a -14b).
4.2 Mute (voice operated switch) function
Pressing "Mute" button you activate mute function that allows you to switch the volume off on the
parent unit (picture 15a).
However, you can still monitor your baby using the sound level lights. When sounds picked up at the
baby unit site reaches the pre-set value (sensitivity), the Mute function will be automatically switched off.
4.3 Microphone sensitivity level setting
To set the sensitivity level, follow these steps:
• Press "Mute" on the parent unit (picture 15a).
• Set the sensitivity by pressing
1 for Low sensitivity, or level 5 for High sensitivity (standard setting is level 3) (picture 15b).
– to decrease the volume. Changing the volume setting on the baby unit
+ or – within 3 seconds to select the sensitivity level required – level
GB
27