Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
The display shows the selected channel. Transmission is not allowed in this
mode. If you press PTT switch (13)
ALERT
(long press)
Note: The SIREN tone only sounds in
WX
mode.
Long press on the ALERT key (10), to
When the function is activated "A" is displayed. If the function is activated
and a tone is detected at the selected weather channel, then the unit
sounds "SIREN" tone. The unit cancels
mode.
During a SIREN tone sound, press the PTT switch (13) to stop the sound.
11) USB CHARGING SOCKET
The USB socket (11) can be used to charge smartphones, tablets or other
rechargeable devices with 5 V - 2.1 A.
12) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the
setting of the equipment into the dashboard easier.
See Cabling Diagram page 55.
13) PTT (Push To Talk)
Transmission key, press to
transmit
listen to
an incoming communication,
TOT (Time Out Timer)
If the PTT switch (13) is pressed for more than 3 minutes, the display starts
blinking and the transmission ends. A beep will sound until the PTT switch
(13) key is released.
14) UP/DN KEYS ON MICROPHONE ~ SCAN
UP/DN KEYS ON MICROPHONE
Press the UP or DN button (14) on the microphone to
UP to
increase
and DN to
decrease
See ROTARY CH KNOB page 7.
SCAN
(very long press)
Press and hold the UP or DN button (14) to
dot between the two channel digits flashes to indicate that the function is
active.
and the current weather channel blinks.
PA
CB
or
mode. It does not sound in
activate/deactivate
the ALERT function.
CB
PA
or
mode and goes to
a message,
is displayed. Release to
disappears.
(short press)
change
the channel.
the channel.
activate
the SCAN function. The
The scanning stops as soon as there is a busy channel. The scanning auto-
matically starts 3 seconds after the end of the transmission and if no key is
activated during 3 s. In
press the UP/DN keys (14) on the microphone to change scan direction.
CB channel Scan
CB
In
mode press and hold the UP or DN button (14) for ± 7 seconds or until
a beep sounds to activate the CB channel Scan.
Press the PTT switch (13) to
channel digits disappears from LCD.
WX
WX channel Scan
WX
In
mode press and hold the UP or DN button (14) for ± 3 seconds or until
a beep sounds to activate the WX channel Scan.
Press for 3 seconds the F key (9) to
the two channel digits disappears from LCD.
Note: The WX channel scan can run in the background while using the
mode.
A) DC-POWER TERMINAL (13,8 V / 27,6 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR EXTERNAL OPTIONAL SPEAKER (8 Ω, Ø 3.5 mm)
D) JACK FOR PA OPTIONAL SPEAKER (Public Address) (8 Ω,
Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MICROPHONE (Ø 2.5 mm)
C) MENU
The order of 11 functions is as described in this manual. However, the func-
tion displayed by entering the MENU will be the last function modified by
the user.
The procedure is the same Whatever the function is:
Press the F key (9) to
enter
1.
Turn the rotary CH knob (3) or use UP/DN keys (14) on the microphone to
select
the menu.
2.
Press the F key (9) to
validate.
on the display.
3.
Turn the rotary CH knob (3) or use UP/DN keys (14) on the microphone to
modify
the value of the parameter.
4.
New press on the F key (9) to
stops blinking. a) Go to point 1 to
PTT switch (13) to
validate
9
SCANNING
mode, turn the CH rotary knob (3) or
exit
CB Channel Scan. The dot between the two
exit
WX Channel Scan. The dot between
MENU.
is displayed.
The parameter of the chosen function blinks
validate
the chosen color. The parameter
adjust
another function or b) Press the
and
exit
MENU.
disappears from the display.
CB
Publicité
Table des Matières
