Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
1.
Turn the rotary CH knob (3) or use the UP/DN keys (14) on the microphone
select
the SWR function.
to
2.
Press the F key (9). The radio automatically goes to
ing PTT switch (13) . The SWR measurement starts. Measurement time is 5
minutes maximum. The remaining time is displayed.
3.
Adjust your antenna.
4.
The beep tone* is continuous when SWR value is equal to1. 0 . The space
between two beeps becomes longer when SWR value moves away from1. 0 .
Volume of the beep tone is adjustable with VOLUME knob (1).
Display shows the SWR value. For example 2. 5 .
5.
Press the PTT switch (13) to
exit
*Please check that the beep volume is set to a comfortable listening level.
See § HOW TO ADJUST SWR page 6.
6) EMG SET 1
Allows to
set
the channel for Emergency Channel 1.
Press the F key (9) to
enter
MENU.
1.
Turn the rotary CH knob (3) or use UP/DN keys (14) on the microphone to
select
the EMG 1 function.
2.
Press the F key (9) to
validate.
3.
Turn the rotary CH knob (3) or use UP/DN keys (14) on the microphone to
select
the emergency channel.
4.
New press on the F key (9) to validate. The channel stops blinking. a) Go to
point 1 to
adjust
another function or b) Press the PTT switch (13) to
and
exit
MENU.
disappears.
5.
exits
If no key is pressed, the unit
the display.
Default emergency channel 1 is 9.
See § EMERGENCY CHANNELS page 8.
7) EMG SET 2
Allows to
set
the channel for Emergency Channel 2.
Press the F key (9) to
enter
MENU.
1.
Turn the rotary CH knob (3) or use UP/DN keys (14) on the microphone to
select
the EMG 2 function.
Points 2 to 5 are identical to § EMG SET 1.
Default Emergency channel 2 is 19.
See § EMERGENCY CHANNELS page 8.
8) VOX SETTING
Press the F key (9) to
enter
MENU.
TX
mode without press-
MENU mode.
disappears from the display.
is displayed.
The current channel blinks on LCD.
MENU after 10 seconds,
disappears from
is displayed.
is displayed.
1.
Turn the rotary CH knob (3) or use UP/DN keys (14) on the microphone to
select
the VOX function.
Three adjustments are possible: Sensitivity L / Anti-vox level A / Vox delay time
t (over and over).
2.
Press the F key (9). The current setting (L, A or t) blinks on the LCD.
3.
Turn the rotary CH knob (3) or press the UP/DN (14) keys on the microphone
move
to
to next setting or...
4.
Press the F key (9). The value of the current setting blinks on the LCD.
5.
Turn the rotary CH knob (3) or press the UP/DN (14) keys on the microphone
adjust
the value of the setting.
to
6.
Press the F key (9) to
7.
Go to point 2 to set both others adjustments of VOX.
8.
Once the settings done, press the PTT switch (13) to
mode. If no adjustment is made for 10 seconds, the unit automatically
the function.
Sensitivity L: allows the adjustment of the microphone (original one or
-
optional vox) for an optimum transmission quality. Adjustable level from1
(high level) to 9 (low level).Default value: 5.
-
Anti-Vox A: allows disabling the transmission generated by the surrounding
noise. The level is adjustable. OF (according the squelch level) and from 0
(without anti-vox) to 9 (low level). Default value: OF.
-
Delay time t: allows avoiding the sudden cut of the transmission by adding
a delay at the end of speaking. The level is adjustable from 1 (short delay)
to 9 (long delay). Default value; 1.
validate
VOX SETTING don't automatically activate the VOX function.
9) PA SETTING
This function allows to
Press the F key (9) to
1.
Turn the rotary CH knob (3) or use UP/DN keys (14) on the microphone to
select
the PASET function.
2.
Press the F key (9) to
3.
Turn the rotary CH knob (3) or use UP/DN keys (14) on the microphone to
select
the operating mode of the PA : I n, OF or PA.
4.
New press on the F key (9) to validate. The parameter stops blinking. a)
Go to point 1 to
validate
and
exit
5.
If no key is pressed, the unit
the display.
I n: the
modulation of the microphone
connected to jack PA.SP. (D). The
11
store
and
validate
the setting.
exit
select
the operating mode of Public Address.
enter
MENU.
is displayed.
validate.
The current value blinks on LCD.
adjust
another function or b) Press the PTT switch (13) to
MENU.
disappears.
exits
MENU after 10 seconds,
is transmitted to external loudspeaker
received signal
the VOX Adjustment
exits
disappears from
is transmitted to the
Publicité
Table des Matières
