Publicité
ONE-WAY VIDEOINTERCOM SYSTEM (no programming required)
SEM7MEW
ON
OFF
Termination
Cat5
switch 6 = ON
1 mm
0,75
2
(com-
(2302E)
mm
2
I terminali L1 e L2 non sono polarizzati.
bined)
L1 and L2 terminals are not polarized.
200 m
150 m
100 m
A+B
Les terminaux L1 et L2 ils ne sont pas polarisés.
max
max,
max
Los terminales L1 y L2 no son polarizados.
120 m
100 m
80 m
B
max
max
max
80 m
60 m
40 m
A
max
max
max
SEC/E
ONE-WAY VIDEOINTERCOM SYSTEM WITH TWO MONITORS
1
2 3
4 5 6
SEM7ME
B
ON
OFF
SEM7MEW
A
SEC/E
1 2 3
TWO-WAY VIDEOINTERCOM SYSTEM WITH TWO MONITORS
User ad-
dress:
ON
16
OFF
SEM7MEW
Termination
switch 6 = ON
B
ON
OFF
SEM7MEW
Termination
switch 6 = ON
T h e
S E M -
7MEW must
also be used
as a monitor
for the second
appartment.
Set Call_Nbr =
16.
A
SEC/2E
L1
1
SET
B
MONITOR
AS MASTER
SEPS/1
SYSTEM
POWER
L N
SUPPLY
L1 L2
A
110-230Vac
L1
BUS
L2
S+
S-
SE=12Vdc - 0,25 A max
1 2 3
PA
PL
L1
L2
L1
L2
L1
1
SEPS/1
L N
L1 L2
L1 L2
110-230Vac
PA = Open door push-
SE = Electric doorlock
L1
L2
S+
S-
SE
SE=12Vdc - 0,25 A max
PA
PL
L1
L2
L1
1
L1
L2
L1
1
SEPS/1
L N
L1 L2
L1 L2
PA = Open door push-
110-230Vac
SE = Electric doorlock
L1
BUS
L2
S+
S-
SE=12Vdc - 0,25 A max
1 2 3
PA
PL
Electric door lock
The external door station has terminals for opening a
DC and AC lock. In the former case, the lock is operated
directly from the system's power supply (maximum
power consumption is limited to 12 Vdc / 250mA). The
installation diagrams presented on the left-hand side
of the page show the connection of a lock even in the
presence of an opening button (PA).The jumper on the
external unit must be left as set by factory.
L1 L2
On the contrary, to use AC electric door locks, an op-
PA = Open door push-
button (optional)
tional transformer (TR) is required, which must be
SE = Electric doorlock
suitably dimensioned according to the lock absorption.
The internal relay contacts allow a maximum absorp-
tion of 24V (ac or dc) / 1A.
SE
It is necessary to
use the SEM7ME
as a secondary mo-
nitor. Refer to the
relevant instruction
manual for configu-
ration as a slave.
TR
The Unlock Mode parameter on the door station should
be configured as follows:
- press the KEY_SET button 3 times (the UNLOCK LED
button (optional)
- press the KEY_1 button to set the NO mode (for
To manage a second door lock, device art. SER01 must
be purchased and installed.
button (optional)
SE
Remove the
jumper
1
2 3
BUS PL S+ S-
BUS PL S+ S-
BUS PL S+ S-
TR
lights up and two beeps are emitted);
locks that must be powered to open. One long beep
is emitted with this setting.) or NC mode (for locks
which must be disconnected from power to open.
Two short beeps are emitted with this setting).
LED_NAME
Remove the
jumper
LED_UNLOCK
LED_TALK
KEY_SET
KEY_4
KEY_3
KEY_2
KEY_1
Mi 2554/3
- 9 -
Publicité
