iHealth BP5 Instructions page 19

ELECTROMAGNETIC COMPATIBILITY INFORMATION
Table 1
Guidance and manufacture's declaration - electromagnetic emissions
The Wireless Blood Pressure Monitor is intended for use in the electromagnetic environment speci ed
below. The customer or the user of the Wireless Blood Pressure Monitor should assure that it is used in
Emissions test
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic
emissions
IEC 61000-3-2
Voltage uctuations/
icker emissions IEC
61000-3-3
Table 2
Guidance and manufacturer's declaration - electro magnetic immunity
The Wireless Blood Pressure Monitor is intended for use in the electromagnetic environment speci ed below. The cus-
tomer or the user of the Wireless Blood Pressure Monitor should assure that it is used in such an environment.
IMMUNITY
IEC 60601test level
test
Electrostatic
± 6 kV contact
discharge (ESD)
± 8 kV air
IEC 61000-4-2
Electrical fast
± 2 kV for power
transient/burst
supply lines
IEC 61000-4-4
Surge ± 1 kV line(s) to line(s)
IEC 61000-4-5 ± 2 kV line(s) to earth
Voltage dips, short
<5 % U
interruptions and
cles
voltage variations
40 % U
T
on power supply
70 % U
T
input lines
<5 % U
IEC 61000-4-11
Power frequency
(50/60 Hz)
3 A/m
magnetic eld
IEC 61000-4-8
NOTE: U
For all ME EQUIPMENT and ME SYSTEMS
such an environment.
Compliance
Group 1
Class B
Class A
Complies
For all ME EQUIPMENT and ME SYSTEMS
(>95 % dip in U ) for 0.5 cy-
T T
(60 % dip in U ) for 5 cycles
T
(30 % dip in U ) for 25 cycles
T
(>95 % dip in U ) for 5 s
T T
is the a. c. mains voltage prior to application of the test level.
T
Electromagnetic environment - guidance
The Wireless Blood Pressure Monitor uses RF energy only
for its internal function. Therefore, its RF emissions are very
low and are not likely to cause any interference in nearby
electronic equipment.
The Wireless Blood Pressure Monitor is suitable for use in all
establishments, including domestic establishments and
those directly connected to the public low-voltage power
supply network that supplies buildings used for domestic
purposes.
Compliance level
± 6 kV contact
± 8 kV air
± 2 kV for power
supply lines
± 1 kV line(s) to line(s)
± 2 kV line(s) to earth
<5 % U (>95 % dip in U ) for 0.5 cy-
T T
cles
40 % U (60 % dip in U ) for 5 cycles
T T
70 % U (30 % dip in U ) for 25 cycles
T T
<5 % U (>95 % dip in U ) for 5 s
T T
3 A/m
Electromagnetic environ-
ment - guidance
Floors should be wood, concrete or ce-
ramic tile. If oors are covered with syn-
thetic material, the relative humidity
should be at least 30 %.
Mains power quality should be that of a
typical commercial or hospital environ-
ment.
Mains power quality should be that of a
typical commercial or hospital environ-
ment.
Mains power quality should be that of a
typical commercial or hospital environ-
ment. If the user of the wireless blood
pressure monitor requires continued
operation during power mains interrup-
tions, it is recommended that the wire-
less blood pressure monitor be powered
from an uninterruptible power supply or
a battery.
Power frequency magnetic elds should
be at levels characteristic of a typical lo-
cation in a typical commercial or hospital
environment.
17