Publicité
SETUP INSTRUCTIONS
3. Tighten the gear from the outside of the pool to attach Part O / P to the liner.
4. Screw Part N onto Part O / P and close the water valve in the locked position to complete the connection.
Filling the Pool with Water:
ATTENTION: Do not leave the pool unattended while filling with water. Continuously check the pool to ensure it is being filled
correctly. Ensure that the belt of the U-Support is completely extended.
It is highly recommended to use tap water for filling to minimize unwanted content, such as minerals. Do not use sea water.
Fill the pool with water after all assembly steps are completed and until the water reaches the welding line, which corresponds to 90%
of the full capacity. Do not overfill as this could cause the pool to collapse. In the case of heavy rainfall, we strongly recommend
reducing the water level to keep it at 90% capacity and avoid the overflow of water.
IMPORTANT: When the pool is 90% full, check that the distance between the water surface and the top of the rails is the same all
around. If it is different, it means that the surface is not level, and we strongly recommend draining the water and adjusting the chosen
location. Never attempt to move the pool with water still in it.
IMPORTANT: Keeping the pool full of water on unlevel ground can cause the bursting of welding points and/or pool collapse, causing
serious personal injury and/or damage to property. Your pool may contain a great deal of pressure. If your pool has a bulge or uneven
side, the sides may burst, suddenly releasing water and causing serious personal injury and/or damage to property. When the pool is
90% full, check the pool for any leaks at the valves or seams and for any evident water loss. Do not add any chemicals to the water
until this has been done.
MAINTENANCE INSTRUCTIONS
Keeping your pool water clean and chemically balanced is necessary. Simply using the filtration system and cleaning the filter
cartridge is not enough for proper maintenance of the water.
It is important to prioritize the maintenance and health of your pool water. If you do not adhere to these guidelines, your and your
family's health might be at risk.
Water Maintenance:
We recommend you use pool chemicals to maintain water chemistry and chlorine or bromine tablets (do not use granules) with
a chemical dispenser.
The chemical maintenance with chemical tablets must be performed with a chemical dispenser or chemical floater. Do not throw
chemical products directly into the water. The chemicals will settle on the bottom of the pool and damage and discolor the liner. In the
worst cases, it will damage the structure of the pool liner.
Pool damage resulting from the misuse, number of users and overall mismanagement of pool water is not covered by the warranty.
Water quality is directly related to frequency of use, number of users and overall maintenance of the pool. The water should be
changed every 3 days if there is no chemical treatment being performed with the water. We recommend that you take a shower before
using your pool, as cosmetic products, lotions and other residues on the skin can quickly degrade water quality. Place a bucket of
water next to the pool to clean users' feet before they enter the water.
Use a pool skimmer for the surface and a vacuum cleaner for the pool bottom regularly to avoid settled dirt. If they are not included in
the set, you can purchase them by visiting our website (www.bestwaycorp.com) or by visiting the nearest pool supply store.
Chemical Usage:
Your pool set may not include a chemical dispenser. In this case, you can purchase one by visiting our website
(www.bestwaycorp.com) or by visiting the nearest pool supply store. Remove the chemical dispenser when the pool is in use. After
performing chemical maintenance and before using the pool, use a test kit (not included) to test the water chemistry. We recommend
maintaining your water's chemical balance as shown in the table below.
Exceeding the following parameters can damage the structure of the liner and create a dangerous situation for the users.
Parameters
Water clarity
Colour of the water
Turbidity in FNU/NTU
Nitrate concentration above that of fill water in mg/l
Total organic carbon (TOC) in mg/l
Redox potential against Ag/AgCI 3,5 m KCl in mV
pH value
Free active chlorine (without cyanuric acid) in mg/l
Free chlorine used in combination with cyanuric acid in mg/l
Cyanuric acid in mg/l
Combined chlorine in mg/l
Please consult your local pool or chemical supply retailer for more information about chemical maintenance. Pay close attention to the
chemical manufacturer's instructions.
Winterization (for APX 365™ pools only)
Polar-Shield™ year-round weather defense allows the pool to stay up during wintertime without completely emptying the pool water.
Values
clear view of the pool bottom
no colour should be observed
max. 1,5 (preferably less than 0,5)
max. 20
max. 4,0
min. 650
6,8 to 7,6
0,3 to 1,5
1,0 to 3,0
max. 100
max. 0,5 (preferably close to 0,0 mg/l)
9
Publicité
