Publicité
SETUP INSTRUCTIONS
Overview
Choosing the Correct Location:
The location chosen where the pool will be installed must respect the
following conditions:
- Because of the combined weight of the water inside the pool and the
users, it is extremely important that the surface chosen is capable of
uniformly supporting the total weight for the entire time the pool is
installed. When choosing the surface, take into consideration that water
may come out of the pool when in use or when it rains. If the water
softens the surface, it may lose its capability to support the pool weight.
- Check the position of the vertical legs and/or the U-supports regularly.
They must always be level with the bottom of the pool. If the vertical leg or
the U-support starts to sink into the ground, drain the pool water
immediately to avoid the pool collapsing due to the uneven load on the frame structure. Change the location of the pool or modify
the surface material.
- The surface must be flat and smooth. If the surface is inclined or uneven, it can create an unbalanced load on the structure of the
pool. This can damage the welding points of the liner and bend the frame. In the worst cases, the pool can collapse, causing serious
personal injury and/or damage to personal property.
- We recommend positioning the pool away from any objects children could use to climb into the pool.
- Position the pool near an adequate drainage system to deal with overflow or to empty the pool. Ensure the pool side with the water
inlet A and outlet B is facing in the direction of the power source, where the filtration system will be connected.
- The selected surface must be clear of any type of object. Due to the weight of the water, any object under the pool could damage or
perforate the bottom of the pool.
- The selected surface must be clear of aggressive plants and weed species. Types of strong vegetation could grow through the liner
and create water leakage. Grass or other vegetation that may cause odor or slime to develop must be eliminated from the
chosen location.
- The selected location must not have overhead power lines or trees. Be sure the location does not contain underground utility pipes,
lines or cables of any kind.
- The selected position must be far from house entrance. Do not position any equipment or other furniture around the pool. The water
that comes out of the pool during use or due to product malfunctions can damage furniture inside the house or surrounding the pool.
- The selected surface must be flat and without holes that can damage the material of the liner.
Suggested surfaces: grass, ground, concrete and all other surfaces that respect the above set-up conditions.
Surfaces to avoid: mud, sand, gravel, deck, balcony, driveway, platform, soft/loose soil or other surface that does not meet the above
set-up conditions.
Follow the important instructions above to choose the correct surface and location to set up your pool. If parts become damaged
because the set-up surface and location does not adhere to these instructions, it will not be considered a manufacturer defect and will
void the warranty and any service claims.
If the selected surface is too soft to hold the frame, install wood or metal plates with a thickness of no bigger than 2 cm (0.79") under
the legs. The plates must not touch the liner or have a sharp area, as this can cause damage and will not be covered under the
manufacturer's warranty.
Additional Guidelines:
Check with your local city council for bylaws relating to fencing, barriers, lighting and safety requirements, and ensure you comply
with all laws.
If a pump and/or ladder is included in the set, refer to the pump's and/or ladder's manual for safety instructions and installation. The
ladder must match the pool size.
If you must change locations during set-up, lift the liner to move it; do not drag it on the ground. The friction between the PVC material
and the ground can damage the pool liner.
Parts & Tools Needed
Compare the parts in your box to the parts listed in this manual.
Verify that the equipment components represent the model that you had intended to purchase. If any parts are damaged or missing at
the time of purchase, visit our website bestwaycorp.com/support.
Assembly Instructions
For installation instructions, scan the QR code printed on the front cover or follow the illustrations inside the manual.
are for illustration purposes only. May not reflect actual product. Not to scale.
Assembly of this pool can be completed without additional tools. Installation takes approximately 30-90 minutes with 2-3 people,
excluding any preparations or water filling (refer to the package for specific information about your purchased item). Please note that
assembly times may vary based on pool size and individual experience.
Bestway is not responsible for damage caused to the pool due to mishandling or failure to follow these instructions.
Helpful Installation Tips:
We strongly suggest opening the package and assembling the pool when the ambient temperature is above 15ºC / 59ºF. The PVC
material of the liner will be more flexible and easier to assemble in this environment.
We suggest you buy a pool ladder (if one is not included in the set) and prepare it before setting up the pool, as it will help whenever
you need to get inside it.
Step 4: Fully extend the support sleeves on the bottom of the liner to ensure the correct positioning of the U supports.
Step 5: When the pool is filled with around 1 cm (0.39") of water, gently smooth out the bottom liner to remove all folds. We
recommend starting from the center of the pool and continuing outwards. You can continue to fill the pool when the floor is smooth
and wrinkle-free.
Step 7: If the connection valve for the pool's inlet A and outlet B is composed of Part N and Part O / P:
1. Unscrew the gear from Part O / P.
2. Insert the smaller end of Part O / P through the inlet from the inside of the pool.
Max. 2 cm / 0.79"
8
Drawings
Publicité
