Publicité
ENGLISH
3.2 Fitting the FingerDetail accessory
You can replace the sanding pad (6) with the FingerDetail accessory (12) provided.
3.2.1 Removing the sanding pad
Fig. 3
1.
Move the lever (15) in the direction of the arrow shown in the figure until it stops.
2.
Remove the front part of the sanding pad (6).
3.2.2 Fitting the FingerDetail accessory
Fig. 4
Insert the accessory (12) into the sanding plate (6) and push it all the way into place.
1.
2.
To fix it, move the lever (15) to its original position.
3.2.3 Inserting the sanding sheet in the FingerDetail accessory
Press the corresponding sanding sheet (13) onto the FingerDetail accessory (12).
1.
2.
Also place sanding sheet on the back of the sanding pad (6). This will prevent the Velcro
from getting dirty.
3.3 Fitting/removing/emptying the dust collection tank
Fig. 5
3.3.1 Fitting the dust collection tank
Before fitting the tank (8), make sure that it is tightly closed.
1.
2.
Insert the tank (8) as far as it will go into the dust extraction port (4). Pay attention to the
guides (16) of the dust extraction port (4).
3.
To fix the tank (8) securely, turn it clockwise.
3.3.2 Removing the dust collection tank
1.
To release the tank (8), turn it counterclockwise.
2.
Remove the tank (8).
3.3.3 Emptying the dust collection tank
1.
Press the tab (9) on the tank (8) to remove the cover (7).
2.
To empty the tank (8), simply shake it.
Then, replace the cover (7).
3.
Note: empty the dust collection tank regularly to ensure optimum suction.
3.4 Connecting/disconnecting the external vacuum cleaner
Fig. 6.
150
PerfectSurface 180 Delta
3.4.1 Connecting the external vacuum cleaner
1.
Insert the adapter (10) into the dust extraction port (4) and push it in as far as it will go.
2.
Connect the hose of the vacuum cleaner to be used to the adapter (10). Make sure that the
vacuum cleaner you use is suitable for vacuuming up sanding debris.
Note:
-
Use a suitable vacuum cleaner. Normal household vacuum cleaners are not designed to
vacuum up sanding debris.
-
If required, you can connect the vacuum cleaner hose directly to the tool, without using
the adapter.
WARNINGS:
-
Risk of fire. Accumulated dust from sanding surface coatings (polyurethane, linseed
oil, etc.) can ignite spontaneously and cause a fire. To reduce the risk, strictly follow the
instructions in the sander and coating manufacturer's manual.
-
Risk of fire. Do not use a vacuum cleaner when sanding wood with nails or metal surfaces,
as sparks may occur. Wear safety goggles and a dust mask. Due to the risk of fire, do not
use the sander to sand magnesium surfaces. Do not use the tool for sanding wet surfaces.
4. OPERATION
-
Before using the sander, read the safety instructions carefully and get familiar with all its
functions.
-
WARNING:
-
Switch off the sander when handling parts or accessories, adjusting settings, cleaning or
when you have finished using it. This will prevent accidental starting, which could cause
injury.
-
Secure the workpiece correctly to prevent it from moving. We recommend that you use a
tool designed for this purpose, such as a vise, for instance.
-
Do not allow the sander or the workpiece to get too hot. Overheating increases the risk of
fire.
-
Please note that when working on it, the workpiece may become hot. Therefore, avoid
touching it until it is completely cool, otherwise you may burn yourself. Do not use
refrigerants or similar products.
Switching off/on the sander
Note:
-
Make sure that the supply voltage matches the rated voltage indicated on the sander's
marking.
ENGLISH
151
PerfectSurface 180 Delta
Publicité
