Publicité
1.7 Intellectual property
This manual and any annexed documents are the property of ELCA
and all rights are reserved. No part of this publication (for example
the structure, the contents, the instructions, the figures, the
diagrams, the photos) may be reproduced or transmitted (including
photocopies and web) for any reason without the written
authorisation of Elca.
2 Series, Radio Remote Control and Unit
The part of the Manual concerns the Receiving Unit of an Elca Radio
Remote Control in the E2 series.
Elca Radio Remote Controls provide a control interface to e used on
Machines to manage the command and control system.
The Radio Remote Controls have been designed to be used at a
suitable distance and position.
The radio remote control in the series E2 consists of a transmitting
unit and a receiving unit.
3 Conformity
It is the responsibility of the recipients of these instructions to:
• check the radio frequency band permitted in the country where
it will be used;
• check that the Radio Remote Control operates inside this band;
• check the country's applicable standards;
• check that the Radio Remote Control operates correctly in
conformity with them.
In no way can the conformity of the Radio Remote Control be
modified, making changes to it or carrying out technical
interventions that change the way it works.
For the instructions and use of the Elca Radio Remote Controls,
local regulations must be respected.
These regulations obligate the protection of the conformity of the
products with local regulations, and the specific standards
regarding the safe use of the Radio Remote Controls or electric
devices, both inside and outside the workplace.
3.1 FCC and IC Conformity statement
Each E2 series' radio remote control working in the frequency band
915.00 - 928.00 MHz complies with the essential requirements of
the following regulations:
• FCC (Federal Communication Commission) Part 15
• IC (Industry Canada) RSS-102
Receiving Unit
AR E29-MINI
FCC ID: 2ABS7-ARE29MINI
IC: 30220-ARE29MINI
3.1.1 Federal Communications Commission (FCC)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions,
may
cause
communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
6
harmful
interference
to
3.1.2 Industry Canada (IC)
This device complies with Industry Canada licence/exempt RSS
standard(s).
Operation is subject to the following two condictions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
3.2 Countries of use
E2 series' radio remote controls working in the frequency band
915.00 - 928.00 MHz can be used in the US and Canadian markets.
4 Manufacturer's identification
Radio Remote Control
Manufacturer
Registered office
Telephone
Fax
E-mail
Site
5 Assistance and spare parts
For technical assistance and/or spare parts, please contact Elca.
When sending a request regarding an Elca Radio Remote Control
the serial number (Serial Num.) of the Radio Remote Control itself
must be provided. The serial number (Serial Num) can be found on
the Unit's data plate (see paragraph 11.3 ).
6 Warranty
The general warranty conditions can be found in the
dedicated section of the website www.elcaradio.com.
7 Safety warnings
7.1 General information
All the warnings and instructions contained in this chapter are
relevant for safety purposes.
Failure to follow the instructions in the Manual supplied by Elca
and applicable safety legal provisions, also local, regulations,
norms and standards can cause serious injuries to Persons and
damage to property.
It is the responsibility of the Manufacturer and/or the designer
of the Machine, the Installer, the Maintenance Technician and
the Persons responsible for the use of the Machine and the
workplace, that the installation, maintenance and use of the
Elca Radio Remote Control and all its components are done only
and entirely in compliance with the instructions provided by
Elca e and in conformity with all applicable safety standards
and regulations in force in the countries where the Machine and
Radio Remote Control are used.
The Manufacturer of the Machine bears responsibility for the
installation and use of Radio Remote Control on any
application.
The Manufacturer of the Machine or whoever intends to use or
install an Elca Radio Remote Control on a Machine should first of all:
• check whether the Machine that you want to equip with a Radio
radio
Remote Control is suitable for being used with a Radio Remote
Control safely and efficiently;
• carry out a comprehensive risk assessment taking into contact
the construction, functional and/or performance characteristics
of the Machine, the use of the Machine, the location and the
environment where the Machine will be used, the structure where
the Machine will be or is installed, the interaction between the
Machine and the other equipment and the personnel, the safety
conditions when the Machine is operating, the effective and
potential different conditions of use, the conditions that can be
created after the installation of a Radio Remote Control and the
characteristics and limitations of the Elca Radio Remote Control.
ELCA S.r.l.
Via del Commercio, 7/b – 36065
Mussolente (VI) - ITALY
+39 0424 578500
+39 0424 578520
info@elcaradio.com
www.elcaradio.com
Publicité
