Publicité
SPECIFICATIONS
90 PSI
33 CFM
6.2 Bar
934L/min
INTRODUCTION
Thank you for purchasing the Alpha
Pneumatic High-Speed Cutter/Grinder. The Ultimate
Work Horse for Stone Fabricators. A wide range of
accessories help you perform many different tasks.
For your safety, please read this manual thoroughly
before you start operating this tool.
ABOUT THE SYMBOLS
According to the hazard level, all safety notes in this
manual are classified into "DANGER", "WARNING"
and "CAUTION".
DANGER! - Death or serious personal injury is
imminent when handling this tool incorrectly.
WARNING! - There is a possibility of death or seri-
ous personal injury when handling this tool incorrectly.
CAUTION! - There is a possibility of personal injury
or property damage when handling this tool incorrectly.
NOTE: In some situations, failure to observe
WARNING notes could result in death or serious per-
sonal injury. Be sure to read and observe the safety
notes to ensure safety and correct use of the
SAFETY INSTRUCTIONS FOR POWER
TOOLS
1. Know Your Power Tool. Read owner's
manual carefully. Learn its applications and limita-
tions as well as specific potential hazards particular
to this tool.
2. Keep Work Area Clean. Cluttered areas and
benches invite accidents.
3. Avoid Dangerous Environments. Keep
work areas as dry as possible. Do not use tool in
presence of flammable liquids or gases. Keep the
area well lit.
4. Keep Children and Visitors Away. All visi-
tors should be kept a safe distance from the work
area. Keep out of reach of children.
5. Don't Force Tool. It will do the job better and
safer at the rate for which it was designed.
10,000 RPM
4.6 lbs
(PWC-658)
2.1kg
(PWC-614)
12,000 RPM
(PWC-514)
5" & 6"
®
3/8" NPSM 1/8" BSPT
6. Wear Proper Apparel. Do not wear loose cloth-
ing or jewelry as it can get caught in moving parts.
Rubber gloves and insulated non-skid footwear
are recommended. Wear protective covering to
contain long hair.
7. Wear Proper Eye Protection. All users and
bystanders must always wear proper personal eye
protection which conform with ANSI/ISEA Z87.1
(CAN/CSA Z94.3). Also, use a face or dust mask
if operation is dusty. Always wear certified safety
equipment.
8. Wear Proper Ear Protection. All users
and bystanders must wear proper personal ear
protection which conforms with ANSI S12.6 (S3.19)
hearing protection.
9. Wear Proper Respiratory Protec-
tion. All users and bystanders must wear
proper personal respiratory protection. Al-
ways use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure.
tool
.
WARNING! Some dust created by power
sanding, sawing, grinding, drilling, polishing and
other construction activities contains chemicals
known to the State of California to cause can-
cer, birth defects, or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks, cement and other
masonry products, and
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depend-
ing on how often you do this type of work.
To reduce your exposure, work in a well ven-
tilated area, and work with approved safety
equipment, such as dust masks that are spe-
cially designed to filter out microscopic particles.
To familiarize with the risks associated with a ma-
terial, consult with your employer, manufacturer/
supplier and government agencies regarding the
5/8"-11
MAX HP
MAX. DISC SIZE
(PWC-658)
1.4
(PWC-658/PWC-614)
M14-2
(PWC-614)
M14-2
(PWC-514)
6" (150mm)
5" (125mm)
(PWC-514)
English
3
Publicité
