Publicité
Liens rapides
Lower Body Panel
Exhaust & Tail-Lamp assembly
Hitch Shown In Proper Position
Equipment Required:
F t
Fastener Kit: 24854F
Kit 24854F
Wrenches: 17mm
Drill Bits: None
Handle
Square end tube tool
Access cover
Vehicle frame
cut-away to show detail
1
2
2
Qty. (4)
10mm -1.25 x 40mm CL8.8 Hex Bolt
1
Qty. (4)
7/16" Conical Toothed Washer
2
1.
You may have to lower spare tire to install hitch. Open vehicle rear hatch door and there is a plastic access cover on the floor
underneath the door that must be snapped open to allow access for tool to lower tire. The tool and handle are located
underneath floor panel behind rear seat on driver's side. Remove square ended tube that goes down through access hole and
p
handle with square hole in it to fit on this tube. Lower spare tire on cable 3 or 4 inches only. It is not necessary to completely
lower or remove spare tire off of cable holder.
2.
Raise hitch into place being careful not to damage plastic rear light housings behind bumper. Hitch mounts to existing
weldnuts located in bottom of frame. Install bolts and conical washers as shown above. Install a flat washer as needed per
side on rear attachments to fill gap between hitch and vehicle frame. Torque bolts to specifications shown below.
3.
Raise spare tire back in to place guiding it forward of the installed hitch. Follow directions on access cover so that you do not
over tighten cable when raising tire.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010 Cequent Performance Products
Vehicle Frame
Bumper Fascia
Drawbar Kit:
3590
Drawbar must be used in
the RISE position only.
To lower spare tire
3
3
Tighten 10mm-1.25 CL8.8 bolts with torque wrench to 42Lb.-Ft. (57 N*M).
Installation Instructions
Acura ZDX
All Models
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Do Not Exceed Lower of Towing Vehicle Manufacturer s Rating or
Hitch type
Weight Carrying
Ball Mount
Bottom view of frame
Hitch mounting
weldnuts
Plastic light housing
Vehicle forward
Insert flat washer between hitch
and vehicle frame as needed,
typical both sides.
Qty. (2)
3
q
Sheet 1 of 3
Max Gross
Trailer WT (LB)
2000 (908 Kg)
Wiring Access Location: B, E
7/16" Heavy Flat Washer
Cequent Performance Products
Another fine
g
g
24854N
3-23-10
Part Numbers:
24854
60270
77226
Max Tongue
WT (LB)
200 (91 Kg)
3
1
2
Hitch
Rev. A
Form: F205 Rev A 5-6-05
Publicité
Manuels Connexes pour Cequent Performance Products 24854
Sommaire des Matières pour Cequent Performance Products 24854
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2010 Cequent Performance Products Sheet 1 of 3 24854N 3-23-10 Rev.
- Page 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2010 Cequent Performance Products Feuille 2 sur 3 24854N 3-23-10 Rev.
- Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2010 Cequent Performance Products Hoja 3 de 3 24854N 3-23-10 Rev.