Publicité
Delay Start
You can delay the start of the cycle in one hour increments up to 24 hours.
To set delay start:
1
Open the door (top controls only) and press the [On/Off] button.
2
Press the [+] button until the display jumps to "h:01"
3
Press the [÷] or [-] button
until
the displayed
time
corresponds
with
your
requirements.
h:01 = 1 hour delay
h:24 = 24 hour
delay
4
Press [Start]
to activate
delay
start
and close
the door
(top
controls
only).
To cancel
delay
start:
1
Press the [÷] or [-] button
until
"h:00"
is indicated
on the digital
display.
2
Press and hold
[Start]
for 3 seconds
to cancel
the cycle.
You may now start
a new cycle.
InfoLight
® (model
dependent
- top controls
only)
An LED illuminates
the
floor
to indicate
the
unit
is running.
If the
appliance
is installed
at eye-level,
the
LED is not visible.
To change
the setting:
1
Open
the door and press the [On/Off]
button.
2
Hold down
the "A"
button
(see page 4) and press
[Start]
until
the display
indicates
"H:00".
3
Release
both
buttons.
4
Press the "A" button
until
the display
shows
"::1.:01".
5
Press the "C" button
to switch
between
"1:01"
= ON and "1:00"
= OFF and press
[Start]
to save.
Cycle
Completion
Signal
(model
dependent
- top
controls
only)
1
Open
the door and press the [On/Off]
button.
2
Hold down
the "A"
button
(see page 4) and press
[Start]
until
the display
indicates
"H:00".
3
Release
both
buttons.
4
Press the "A" button
until
the display
shows
"b:02".
5
Press the "C" button
to increase
or decrease
the tone
"b:00"
= OFF and "b:03"
= LOUDEST
6
Press [Start]
to save setting
and close
the door.
Intensive
Drying
The final rinse uses a higher temperature
which improves
the drying
results. The running time may increase slightly.
To turn
intensive
drying
on:
1
Open
the door
(top controls
only)
and press the [On/Off]
button.
2
Hold down
the "A"
button
(see page 4) and press
[Start]
until
the display
indicates
"H:00".
3
Release
both
buttons.
4
Press the "A" button
until
the display
shows
"d:00".
5
Press the "C" button
to turn
intensive
drying
on or off.
"d:0:l."
= ON and "d:00"
= OFF
6
Press [Start]
to save setting
and close
the door
(top
controls
only).
Auto
Power
Off
To save energy,
the dishwasher
is turned
off 1 minute
after
the wash
cycle
ends.
Auto
Power
Off can be
adjusted
from
P:00 to P:02.
To change
the factory
setting
(P:01):
1
Open
the door
(top controls
only)
and press the [On/Off]
button.
2
Hold down
the "A" button
and press
[Start]
until
the display
indicates
"H:00".
3
Release
both
buttons.
4
Press the "A" button
until
the display
indicates
"P:0::I.'.
5
Press the "C" button
until
the display
corresponds
with
your
requirements.
P:00 = dishwasher
does
not turn
off automatically
P:0::I. = dishwasher
turns
off automatically
after
1 minute
P:02 = dishwasher
turns
off automatically
after
120 minutes
(2 hours)
6
Press [Start]
to save the setting
and close
the door
(top
controls
only).
10
Publicité
