Publicité
MODEL: PXL31
!
CAUTION:
CAUTION: It is advisable to test the
depth
on
a scr ap wor kpi ece
to
determine the required depth for the
application.
To determine depth of drive, first adjust
the air pressure and drive a test
fastener. Never exceed
110
psi.
FIRING THE TOOL
The tool is equipped with a selectable trigger
with two firing modes:
SEQUENTIAL FIRING MODE
Single sequential actuation provides the most
accurate fastener placement. This is
considered to be more restrictive mode of
operation, suitable for less experienced users.
To use the tool to drive nails in this actuation
mode, work contact element and trigger must
be used in a specific order.
1.
Disconnect the tool from the air source.
2.
Press the selectable firing mode button,
turning the selectable firing mode switch
to the upwards, the firing mode indicator
should be pointing at the single nail icon.
3.
Connect the tool to the air source.
4.
The
work contact
element must be
completely depressed by placing the nose
of the tool against the workpiece.
5.
The trigger must be pulled firmly and then
released.
6.
The tool must be allowed to recoil away
from the workpiece.
To continue operation in a separate location,
move the tool along the workpiece, repeating
step 4 through 6.
Selectable firing mode switch in sequential fire
mode position
10
HTTP://WWW.FREEMANTOOLS.COM
Note:
If the trigger is pulled before the work contact
element is depressed, the tool will not operate.
CONTACT ACTUATION MODE
Contact actuation allows very fast, repetitive
fastener placement.
To use the tool to drive nails in this actuation
mode the work contact element and trigger can
be actuated in any order.
1.
Disconnect
the tool
from the air source.
2.
Press the selectable firing mode button,
turning the selectable firing mode switch in
the downwards position, the firing mode
indicator should be pointing at the multi-nail
icon.
3.
Connect tools to the air source.
4.
Pull and hold the trigger with the tool off the
workpiece.
5.
Press the work contact element against the
work piece. A nail will be driven.
6.
The tool must be allowed to recoil away
from the workpiece.
7.
Move the tool along the workpiece with a
bouncing motion. Each time the work
contact element is depressed a nail will be
driven.
8.
As soon as the desired number of nails has
been driven, remove finger from trigger.
Selectable firing mode switch in contact
actuation mode position
NOTE:
This actuation mode is recommended when
less precise nail placement is required.
Extreme care should be taken because a
will be driven when the work contact element is
pressed against any surface.
Since the tool can be actuated without
removing the finger from the trigger, this is
considered to be a less restrictive mode,
suitable for more experienced users.
1-888-669-5672
MODEL: PXL31
!
WARNING:
Remove the finger from the trigger
when not driving nails. Always carry the
tool by the handle only.
!
WARNING:
The tool must be allowed to recoil
away from the work piece. Do not
drive a nail on top of another nail.
!
WARNING:
During
normal
use
recoil
immediately
fastener. This is a normal function of
the tool. Do not attempt to prevent
the
recoil
by
holding
against the work. Restriction of the
recoil
can
result
fastener being driven from the tool.
Grip the handle firmly and let the
tool do the work. Failure to heed
this warning can result in serious
personal injury.
!
WARNING:
Always know the operational mode of
the tool before using. Failure to know
the operational mode could result in
death or serious personal injury.
!
WARNING:
An improperly functioning tool must not
be used. Do not actuate the tool unless
the tool is placed firmly against the
work place.
!
CAUTION:
Check the operation of the work
contact element trip mechanism before
each use. The WCE must move freely
nail
without binding through its entire travel
distance. The WCE spring must return
the WCE to its fully extended position
after being depressed. Do not operate
the tool if the WCE trip mechanism is
not operating properly. Personal injury
may occur.
HTTP://WWW.FREEMANTOOLS.COM
WORK CONTACT ELEMENT (WCE)
Disconnect the tool from the air source.
1.
Remove all fasteners from the magazine.
2.
3.
Make sure the trigger and work contact
element move freely up and down without
sticking or binding.
Connect the tool from the air source.
4.
5.
Depress the work contact element against
the work surface without pulling the trigger.
The tool must not operate. Do not use the
tool if it operates without pulling the trigger.
Personal injury may
6.
Remove the tool from the work surface. The
work contact element (WCE) must return to
the
tool
will
its original down position. The tool must not
after
driving
a
operate. Do not use the tool if it operates
while lifted from the work surface. Personal
injury may
happen
the
tool
7.
Pull the trigger and depress the work
contact element(WCE) against the work
in
a
second
surface. The tool must not operate.
8.
Depress the work contact element (WCE)
against the surface. Pull the trigger. The tool
must operate.
MAINTENANCE
!
WARNING:
Any time inspection, maintenance, and
cleaning are going to be carried out:
Disconnect the tool from the air
source.
◆Empty the magazine completely.
ANTI-DUST
Each tool is packed with an anti-dust cap on
the air connector, check it after unpacking.
Keep the air connector covered with the anti-
dust cap when the tool is not in use.
1-888-669-5672
happen
.
.
11
Publicité
