Publicité
RELEASE OF LIABILITY
By assembling and inflating this product, you agree that you have read and understand the entire World of Watersports' product
manual, including all instructions and warnings contained in that material prior to using this product. You additionally agree that
you will ensure any additional or subsequent users of this product will read and understand the entire owner's manual. Misuse or
improper use of this product could result in risks, dangers and hazards which can result in serious injury or death. The risks and
dangers that can be encountered through the improper use of this product can be avoided by reading and following the warning
guidelines listed within the owner's manual and by proper use of this product. Your assembly and use of this product shall be
evidence of your agreement, to the fullest extent permitted by law, to properly follow the instructions and abide by the warnings
set forth within the product manual. Your assembly and use of this product shall also constitute a release, to the extent permitted
by law, by you and by any third party permitted by you to use, in any manner, this product, to World of Watersports from any and
all liability for any loss, damage, injury and/or expense that you or any user of this product may suffer as a result of the use of
this product. This release shall extend to any loss, damage, injury or expense due to any cause whatsoever, including negligence
or breach of contract on the part of World of Watersports and/or any party participating in the design and/or manufacture of this
product. The terms of this release shall be effective and binding upon you, your heirs, next of kin, executors, administrators, assigns
and representatives. Your assembly and use of this product shall constitute your agreement to assume and accept any or all known
or unknown risks of injury to you and/or to third parties through the use of this product. World of Watersports and related parties
have not made and hereby expressly deny any oral or written representation and/or warranty, including warranty for a particular
purpose, other than what is set forth herein and in the World of Watersports' owner's manual.
This WOW Product Manual applies to the following item listed below please read and follow all warnings and information
Product Name
Model#
Approximate Inflated Size
Cascade Pool Slide
22-WSL-4346
248cm x 144cm x 111cm
Patent Pending Package Contents: 1 WOW SLIDE, 1 Repair Patch, 1 Product Manual
THE BEST AIR PUMPS TO USE TO INFLATE YOUR TUBE ARE THE FOLLOWING
1. 110 Volt Electric Pump - E.g. WOW 2.0 to 3.0 PSI High Pressure Air Pump
or any 110 Volt Electric Pump with 2.0 to 3.0 PSI
2. WOW Double Action Hand Pump or Foot Pump specifically designed for towables
3. 12 Volt Pump pumps can also be used but their maximum output is only .8 psi so a secondary pump such a hand
pump or foot pump will need to be used.
4. Leaf Blower
5. Shop Vac or vacuum with two-way switch
6. Do NOT use an air compressor.
1.
2.
GENERAL INSTRUCTIONS
1. Two or more adults are recommended for setup. No tools are required for the assembly.
2. The product must be installed on a flat and level surface at least 6.5 ft (2 meters) away from any structure or obstruction such
as a fence, garage, house, overhanging branches, laundry lines or electrical wires.
3. Locate the slide out of direct sunlight to reduce the likelihood of scalding. A product that faces north will receive the least
direct sunlight.
4. Carry the slide (in its package) to the selected site before inflating. Do not inflate the product and drag it since it may result in
leaks or damage. If you do need to move the slide 2 people can lift the slide by using the handles located on each side of the
slide. Please position the slide location in the deep end of the pool such that the slide exit is free from obstructions.
5. Slowly unfold the product and inspect the product for rips, tears or punctures.
Do not use if the product is damaged.
PROPER INFLATION
Proper inflation is the key to optimum performance and durability of this product. While in use, the cover should be taught with few
wrinkles. If your product has no cover and is constructed out of PVC material only inflate until firm. Once inflated you should test
whether there is enough air in the product by having an adult kneel on the product. If the product is properly inflated, then the adult
will barely sink into the product while standing on top of it. If the product is under inflated damage can occur to the product while in
use and the warranty will be voided. It is important to monitor the amount of air in the product once the item is in use. Continue to
make sure that the product is properly inflated.
When not in use, be sure to remove some air from the product and put in a shaded area. If you leave a full produ
the sun it will cause the air inside to expand, causing serious damage to the seams and I-beams of the product.
Check and adjust inflation levels each time you use the product.
Person
Approximate Weight Limit
98in x 57in x 44in
1
200Ibs./90kg.
3.
4.
2
SETUP INSTRUCTIONS
1. Inflate the product with a air pump or foot air pump until the surface is firm to the touch. If there is any straining at the seams, the
product is over-inflated. If any seam begins to strain, immediately stop the inflation and release air to reduce the pressure until
signs of stress on the seam are gone. Do not over-inflate or use high pressure air compressor since it may result in seam leaks.
The air inside the slide will expand as the temperature increases: double check that the slide is not over inflated throughout the day.
2. Find the valve and inflate the middle main body of the slide first until firm.
3. Inflate the top right and left pontoon rails of the slide until firm.
4. Inflate the slide's end bumper chamber until firm.
5. Double check all inflation chambers are firm and close and secure all valves properly.
6. Check the position of the slide location in relationship to the pools edge and water. Place the slide on the deck of the in-ground
swimming pool such that the distance from the deck to the water surface is no greater than 12 inches (30 cm). WARNING: Make
sure the distance between the deck of the in-ground swimming pool and the water surface does not exceed 12 inches (30 cm)
and the end bumper chamber is touching the water surface.
7. Locate the water ballast chambers on the bottom front left and right part of the slide. Find the valves on both water ballast
chambers and open and fill with water. By filling the water ballast chambers the slide will offer more secure stable sliding by
making the slide stay put and avoid shifting back as the slide is in use. DO NOT TRY TO MOVE THE SLIDE WHILE THE WATER
BALLAST CHAMBERS ARE FULL OF WATER. PLEASE DRAIN BEFORE MOVING THE SLIDE.
8. Connect the garden hose to sprayer valve and set water sufficient to adequately wet the sliding surface. Route the garden hose
away from traffic to prevent any tripping hazard.
Do not modify this product and/or use accessories not supplied by the manufacturer.
SLIDE USE
1. Do not leave children unattended while slide is in use.
2. Adults should closely supervise children when they are using the slide.
3. Younger children may have difficulty climbing up the slide. Provide hands on help to younger children.
4. Only one child on the slide at a time. Make sure pool area below slide is clear before
allowing the next user to climb the slide.
5. Do not use slide while wearing or holding sharp objects, such as jewelry, hair pin, that can
puncture the product.
6. Child should be positioned in the center of the sliding surface before going down the slide.
hose hookup
side rail
valve location
main slide body
valve location
MAINTENANCE
• You may clean your product using soap and water or mild detergent.
• Never use strong cleaning agents.
• The product, when clean and dry, can be deflated and stored in a cool, dry area out of direct sunlight.
• To deflate, simply unfasten the entire valve from the base. Note to unfasten all valves if you have multiple valves on
your product
• Avoid storing this product in areas of extreme temperatures and please take precautions against animals and rodents.
PRODUCT STORAGE
To prepare the product for storage please make sure that it is completely dry to prevent mildew and rot. Release all of the air from
the chamber(s) and fold the product. If possible please store these products in a controlled temperature and do not expose the
product to temperatures less than 40 degrees F. Cold temperature will damage the PVC material and cause it to crack at the folds.
Warranty Policy
WARRANTY: WOW World of Watersports warrants, to the original purchaser only, that their high performance products, when
used for normal recreational purposes, are free from defects in material and workmanship for a period of 1 year from the date of
purchase. Any implied warranties are also limited in duration to the 1 year period from the original date of purchase. Our warranty
excludes products for rental, for hire, and other uses not considered normal recreational purposes. WOW World of Watersports
ct sitting in
will not be held liable for incidental or consequential damages. Note: The above warranty is only applicable to products purchased
inside the U.S.A. For all products purchased outside the U.S.A. the warranty is limited to 90 days.
water ballast fill location
slide bumper valve location
3
dual
sprinklers
Publicité
