Publicité
clockwise.
5. Double check the tension set by the automatic chain
tensioning knob. The correct chain tension is reached
when the chain can be raised approx. Half the drivelink
depth from the guide bar in the center. This should be
done by using one hand to raise the chain against the
weight of the machine. (See Fig. E2)
NOTE: The chain is properly tensioned when it can be
lifted off of the Guide Bar and the drivelink is within the
rail of the Guide Bar.
NOTE: The chain will stretch while cutting and lose
proper tension. When the chain becomes loose,
completely unscrew the chain tensioning knob or turn
the knob around three full turns in a counter-clockwise
direction, then retighten the chain tensioning knob to
properly reset the chain tension by repeating Steps 1-4
listed above.
LUBRICATION (See Fig. F)
IMPORTANT: The Chainsaw is not filled with oil.
It is essential to fill with oil before use. Never
operate the Chainsaw without chain oil or at an
empty oil tank level, as this will result in extensive
damage to the product.
NOTE: Chain life and cutting capacity depend
on optimum lubrication. Therefore, the chain is
automatically oiled during operation.
FILLING OIL TANK:
WARNING: Removing the battery pack before
filling the oil tank.
1. Set Chainsaw on any suitable surface with oil filler cap
facing upward.
2. Clean area around the oil filler cap with cloth and
unscrew the cap by turning it counter clockwise.
3. Add bar and chain oil until tank is full.
4. Avoid dirt or debris entering oil tank, refit oil filler cap and
tighten by turning clockwise until hand tight.
IMPORTANT: To allow venting of the oil tank,
small breather channels are provided between
the oil filler cap and the strainer, to prevent
leakage, and ensure machine is left in a horizontal
position when not in use.
It is important to use bar and chain lubricant (not
provided) that is formulated to perform over a wide
temperature range with no dilution required. This can
be found at the location where you purchased this saw
or your local hardware store. Do not use dirty, used or
otherwise contaminated oils. Damage may occur to
the bar or chain. Use of non approved oil will void the
warranty.
Do not swallow. If swallowed, call a physician
immediately. Keep out of reach of children. Store away
from heat or open flame.
CHECKING THE AUTOMATIC OILER
Proper functioning of the automatic oiler can be checked
by running the Chainsaw and pointing the tip of the
guide chain bar towards a piece of cardboard or paper on
the ground. If an increasing oil pattern develops on the
cardboard, the automatic oiler is operating fine. If there
is no oil pattern, despite a full oil reservoir, contact Worx
Cordless Chainsaw
customer service agent or Worx approved service agent.
CAUTION: Do not touch the ground with the
chain. Ensure safety clearance of 30cm.
OPERATION
1. BEFORE USING YOUR CORDLESS TOOL
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert or
allow metallic objects into your charger or battery pack
connections because of an electrical failure and hazard will
occur.
NOTE: Your battery pack is UNCHARGED and you must
charge once before use.
The battery charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another battery
charger.
2. CHECKING THE BATTERY CHARGE CONDITION (See
Fig. G)
The battery level can be known from the battery indicator
light by pressing the button beside the lights.
NOTE: Fig. G only applies for the battery pack with battery
indicator light.
3. CHARGING YOUR BATTERY PACK (See Fig. H)
The Li-ion battery is protected against deep discharging.
When the battery is empty, the machine is switched off by
means of a protective circuit. Each battery must be fully
charged before the first use.
In a warm environment or after heavy use, the battery pack
may become too hot to permit charging. Allow time for the
battery to cool down before recharging.
NOTE: Always fully charge the two batteries at same
time. More details can be found in charger's manual.
4. TO REMOVE OR INSTALL BATTERY PACK (See Fig. I)
Depress the battery pack release button to remove the 2
battery packs from your tool. After recharging, insert the
2 battery packs into the battery ports. A simple push and
slight pressure will be sufficient until a click is heard. Check
to see if the battery is fully secured.
Note:
•
When removing the battery pack, hold it firmly to
avoid dropping and injury.
•
This machine will only run when 2 batteries are
installed. It is recommended to use the same two
batteries and charge the two batteries at the same
time.
•
When you use two batteries with different power,
the machine will only run to the lower common
denominator.
5. SWITCHING ON AND OFF (SEE FIG. J)
ATTENTION: Check the battery packs before using
your cordless tool. Only use the battery pack listed in
the accessories section.
For switching on the tool, press the lock-out button, then
fully press the on/off switch and hold in this position. The
lock-out button can now be released.
For switching off, release the on/off switch.
NOTE: The chain brake must be activated in order for the
15
EN
Publicité
