Publicité
EN
h. Never use damaged or incorrect saw blade mounting means such as flanges, saw blade washers, bolts or nuts. These mounting means were specially
designed for your saw, for safe operation and optimum performance.
i. Never stand on the table saw, do not use it as a stepping stool. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.
j. Make sure that the saw blade is installed to rotate in the proper direction. Do not use grinding wheels, wire brushes, or abrasive wheels on a table saw.
Improper saw blade installation or use of accessories not recommended may cause serious injury. Use the correct saw blade for the material that is to be
processed. Only use a saw blade with a diameter that corresponds to the information given on the saw. Only use saw blades that are labeled with a
rotational speed equally high as or higher than what is labeled on the electrical tool. Only use saw blades that are recommended by the manufacturer and
that comply with EN 847-1 if they are intended to cut wood or other similar materials. Carry out longitudinal cuts with an incline not on the side towards
which the incline occurs. Wear suitable personal protection equipment, such as: hearing protection, safety gloves when handling saw blades.
Requirements for operating staff
The operating staff must carefully read the Operating Instructions before using the appliance. Since the use of the device if handled incorrectly can entail
considerable risks, only knowledgeable persons may be entrusted with the use of it. The operator must be appropriately trained in setting up, operating and
using the machine.
Qualifications: Persons over 16 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge
under supervision of the trainer during occupational education.
Minimum age: Persons over 16 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge
under supervision of the trainer during occupational education.
Training: Using the appliance only requires corresponding training by a professional or the Operating Instructions. No special training is necessary. The
operator is responsible for accidents or risks to third parties.
Specified Conditions of Use
Use this circular saw to cut only wood and wood like products. Never use the Circular table saw to cut materials other than those specified in the
instruction manual.
Residual Risk
Rip cutting, cross cutting, mitre cutting and bevel cutting using max. one mounted saw blade. Please observe that the cutting of bevels/wedges and
complex covered cutting procedures are not permitted. Only cut materials that are similar to wood and ensure the material is fed forwards slowly and
evenly. Hard materials, feeding the material forwards too quickly and foreign objects in the material can lead to overheating and the saw teeth breaking
off. Despite the observance of the operating instructions there still may be some hidden residual risks.
Risk of injury!
Always keep hands away from the path of the saw blade. In spite of compliance with all relevant design regulations, dangers may still present themselves
when the machine is operated, e.g.: a. Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation,
b. noise emissions, wood dust emissions.
Emergency procedure
Conduct a first-aid procedure adequate to the injury and summon qualified medical attendance as quickly as possible. Protect the injured person from
further harm and calm them down. If you seek help, state the following pieces of information, a. accident site, b. accident type, c. number of injured
person(s), d. injury type(s).
Maintenance
Unplug the machine before any work on it. Prior to every use, visually check the machine to rule out any defects, in particular on the power cable and the
plug.
WARNING The appliance must not be used if damaged or safety equipment is defective. Replace any worn-out and damaged parts. If the device is defective,
the repair has to be made exclusively by the customer service. Use only original accessories and original spare parts. Only a regularly maintained and treated
appliance can serve as a satisfactory aid. Insufficient maintenance and care can lead to unforeseen accidents and injuries. If the replacement of the supply
cord is necessary, this has to be done by the manufacturer or his agent in order to avoid a safety hazard.
Environmental Protection and Disposal
The disposal instructions are based on the icons placed on the appliance or its gummy package. The packaging protects the machine
against damage during transport. Packaging materials are usually chosen based on environment aspects and waste treatment prin-
ciples and are therefore recyclable. Returning the packaging into material circulation saves raw materials and reduces waste produc-
tion. Parts of packagings (e.g. foils, styropor®) can be dangerous for children. Do not dispose of electrical appliances in household
waste; use the local collection points. Ask your local authority where the collection points are to be found. If electrical equipment is
disposed of in an uncontrolled manner, weathering can lead to dangerous substances entering the groundwater and from there the
food chain, or the flora and fauna can be poisoned for years. If you replace the device with a new one, the seller is legally obliged at
the least to take back the old one to be disposed of free of charge.
5
WWW.NIKOLAOUTOOLS.GR
Publicité
