Publicité
Cleaning
DANGER! Risk of injury! Pull out the
power plug before conducting any work on
the tool.
Cleaning overview
After each use
What?
Empty the dust bag.
Regularly and according to the operating condi-
tions
What?
Clean the ventilation slots of
the motor to remove dust.
Error/Fault
Unit does not work.
Sanding performance too low.
Malfunctions are often caused by minor faults. You can
easily remedy most of these yourself. Please consult
the following table before contacting the vendor. You will
save yourself a lot of trouble and possibly money too.
Disposal
Disposal of the appliance
A crossed-out wheelie bin icon means: Batteries
and rechargeable batteries, electrical or electronic
devices must not be disposed of with household
waste. They may contain substances that are
harmful to the environment and human health.
Consumers must dispose of waste electrical devices,
spent portable batteries and rechargeable batteries
separately from household waste at an official collection
point to ensure that these items are processed correctly.
The product can be returned free of charge in accord-
ance with the legal requirements, for example through a
municipal waste disposal company or a dealer.
Batteries, rechargeable batteries and lamps
that are not permanently installed in waste
electrical equipment and can be removed in
a non-destructive way must be removed and
disposed of separately before disposal of the equip-
ment. Lithium batteries and rechargeable battery
packs of all systems are only to be handed in to the
waste collection points in a discharged state. The bat-
teries must always be protected against short circuits
by taping off the poles.
All end users are responsible for deleting any per-
sonal data stored on waste devices prior to their dis-
posal.
Disposal of the packaging
The packaging consists of cardboard and
correspondingly marked plastics that can
be recycled.
How?
Open the zip (15) and re-
move the dust (► P. 4,
fig. 4).
How?
Use a vacuum, hand
brush or paint brush.
Cause
Device is faulty?
Sanding belt not suitable for the ma-
terials?
Is the sanding belt worn out?
What?
Clean the device.
Troubleshooting
What to do when something doesn't work ...
DANGER! Risk of injury! Unprofes-
sional repairs may mean that your unit will
no longer operate safely. This endangers
you and your environment.
Malfunctions are often caused by minor faults. You
can easily remedy most of these yourself. Please
consult the following table before contacting the ven-
dor. You will save yourself a lot of trouble and possibly
money too.
Remedy
Contact your local vendor.
Change the sanding belt (► Fitting
the sanding belt – p. 26).
– Make these materials available for recycling.
Technical data
Item number
Rated voltage
Capacity
Idle belt speed
Protection class
Dimensions of sanding belt
Sound power level (L
WA
Sound pressure level (L
Vibration**
Dimensions
*)
The noise emission values indicated have been measured according to a
standardized test method and can be used to compare one power tool with
another. The noise emission values indicated can also be used for a prelim-
inary assessment of the exposure. Warning: The noise emissions during the
actual use of the power tool may differ from the indicated values, depending
on the way in which the power tool is used, in particular what type of work-
piece is being machined. Safety measures must be defined to protect the
operator, based on an estimation of the vibration load during actual condi-
tions of use (taking into consideration all parts of the operating cycle, such
as time periods when the power tool is switched off and time periods when
it is switched on but running without a load).
Noise emission specifications according to the German Product Safety Act
(ProdSG) or the EC Machinery Directive: The sound pressure level at the
workplace may exceed 80 dB(A). If this is the case, the user must take noise
protection measures (e.g. wearing appropriate hearing protection and tak-
ing regular breaks).
**) The specified vibration emission value was measured in accordance with a
normed test procedure and can be used in order to compare one tool with
another. The specified vibration emission value can also be used for an
introductory evaluation of the exposure. The vibration emission value may
fluctuate from the specified value during actual use of the power tool. These
fluctuations will depend on the way in which the power tool is used. Try to
keep vibrations to a minimum. One method of reducing the vibration load is,
for example, limiting the length of time you work with the tool. All parts of the
operating cycle must be taken into account for this purpose (for example,
also including times in which the power tool is switched off and times in
which it is switched on, but is running without load). Determination of vibra-
tion emission values in accordance with .
GB
How?
Wipe the unit with a damp
cloth.
380592
230–240 V~, 50 Hz
900 W
200–400 m/min
II
533 × 76 mm
)*
104 dB(A)
(K = 3 dB(A))
)*
96 dB(A)
PA
(K = 3 dB(A))
< 6,45 m/s²
(K = 1,5 m/s²)
365×160×150 mm
27
Publicité
