Publicité
Press buttons of setting 16 and 15 together for 3s, week indicator "6" flashes and time setting is activated. Select a day by 14 or 15; press 16
then Hour Indicator "5" flashes, again by 14 or 15 buttons to set Hour. Again press 16 for minute setting ( minute indicator 7 flashes ), set the
desired minute by buttons 14 or 15 , after that press button 16 and save all setting, or just leave it 5s, all setting is saved.
Temp. Setting
− Press button 16 , temp indicator flashes and its setting is activated. Press 14 or 15 to set the temperature and 16 to save it, or just leave it 5s,
setting is saved automatically.
− Press 14 / 15 on the remoter for required temp and save the setting by OK.
High/Low heat Setting
14 button runs low heat setting ( indicator 11 light on), 15 button runs high heat setting (indicator 10 light on), or through shifting button 21 on the
remote control to choose high.
Child-lock Setting
Press both 14 and 15 for 3s, child lock is on, system is locked and no setting could be done. After 3 s, display shows again area temperature.
Methods to unlock:
Press both 14 and 15 for 3s, the unit is unlocked.
Display buttons activation
Normally display buttons light are off when unit is working, touch the panel area below temperature, they are on again.
ECO Function
Press both setting button 16 and 14 for 3s ( or press button 19 on remote control), ECO function runs. In this mode, display shows only some
indicators ( depending on what setting shave been done before ECO)
Methods to lock ECO function
Press any button on display 2) Press ECO button 19 on remote control.
Asleep
In 10s, if no button is pressed when unit is heating, it enters to asleep mode and only shows area temperature.
Open-window Detection
When area temperature decreases 3°C or more in 2mins,heater activates open window detection and displays indicator 1 with a Buzz sound,
then stops heating.
Day/Week Timer Shifting
Press button 20 to shift between day timer & week timer settings. In week timer mode, indicator „WeekTimer" is on; in day timer mode, indicator
„DayTimer" is on.
Day timer (Timing Stop Heating)
Display shows indicator "Day Timer" in this mode. First for Hour, press "Set " on remote controller,14 or 15 buttons for concise one. Then for
Minute, press "Set " again and 14 or 15 buttons for concise one, press button "OK " and save them.
Instant Cancelling
To delete all former setting （day timer or week timer), you just need to press 16 on the display for 10 s.
Week Timer (Timing to Start Heating
Week timer mode enables "4" periods a day, and "7" days a week. Display shows indicator „WeekTimer" in this mode; press "Set " on remote
controller for a day first (indicator "6" flashes), by 14 or 15; then the 1st period: press button " Set" for a start time, same through 14 or 15, then
press button "Set " for a stop time, and again through buttons of 14 or 15. After setting the1st period, then 2nd period.... 3rd period...4th period.
And 2nd day，3rd day... ... ... 7th day. When all needed setting is completed, press button " OK" and save them.
Turn Off
Turn off switch 13 , heater stops working, and turn off power supply, heater is power off.
BATTERY CHANGE
1.
To unlock battery, gently pull the latch open with the cover.
2.
Insert new CR2032 battery, note their required polarity (+/-)
3.
Close the battery cover so that the latch locks.
CLEANING AND MAINTANCE
Before cleaning your heater, switch off the heater and allow it to cool. Disconnect the electricity supply to the appliance. The outside can be
cleaned by wiping it over with a soft damp cloth and then dried. Do not use abrasive cleaning powders or furniture polish, as this can damage
the surface finish. To release the heater from the wall, for cleaning or redecoration, just open the screw bolt cap and unscrew the bolts to take
off from the wall. For short term storage, just plug off the heater and leave it away; for long term storage, you can dismantle from the wall or cover
it with some material.
TROUBLESHOOTING
If your heater fails to operate, please follow these instructions:
• Ensure that your circuit breaker or fuse is working properly.
• Be sure the heater is plugged in and that the electrical outlet is working properly.
• If the ON/OFF switch is not illuminated at ON position, send it to service center for reparation directly.
NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEE THE WARRANTY INFORMATION FOR INSTRUCTIONS.
PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER YOURSELF. DOING SO MAY VOID THE WARRANTY AND COULD
CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM STILL PERSISTS, PLEASE CONTACT THE DISTRIBUTOR..
RECYCLING
Publicité
