Publicité
– Press the On/Off button [ ] (8). [ON] appears in
the display (5): the device is now in standby
mode.
– Press the [
] button (7) once and set the desired
power level with buttons [−] (4) and [+] (6).
– Press the [
] button (7) again and set the
desired cooking temperature with buttons [−] (4)
and [+] (6).
– Press the [ ] button (3) to enter timer function
and set the desired cooking time with but-
tons [−] (4) and [+] (6).
– Press [−]/[+] briefly to set the cooking time in
intervals of minutes. Keep [−]/[+] pressed for at
least 3 seconds in order to set the cooking time
to 10-minute intervals.
– If needed, briefly press the [ ] button (3) to
clear the cooking time then reset.
– The set time will be adopted after 5 seconds
and the device starts the cooking process.
– After the time has elapsed, the device switches
off automatically and returns to the standby
mode.
– To terminate the cooking process at any time,
press the On/Off button [ ] (8).
– To cook again, press the On/Off button [ ] (8)
once, then the [
] button (7), followed by the [ ]
button (3) to enter the desired cooking time.
– The device switches off automatically after two
hours if the set cooking time is not longer than
that.
– The fan continues to work for 1 minute after the
cooking is complete in order to dissipate the heat.
Information on energy consumption
The energy consumption of the appliance was calcu-
lated in accordance with EN 60350-2.
– Keep the power consumption to a minimum.
Error/Fault
Device does not work.
Error code
E0
E1
E2
E3/E4
E5
– Only adjust the power to high as necessary.
Cleaning and maintenance
Cleaning
– Wipe down the device with a dry or lightly mois-
– Carefully clean the ventilation slots from dust and
Troubleshooting
What to do when something doesn't work...
In many cases, small defects can lead to a malfunc-
tion. You will usually be able to deal with these your-
self. Please consult the following table before con-
tacting the store department. This may save you a lot
of effort and quite often money.
Cause
Device is faulty?
No power supply?
Is the On/Off switch set to[0]?
Cause
Without cookware or Incompatible
cookware used
IGBT sensor open circuit/short circuit Contact the supplier.
IGBT overheated.
Voltage > 270 V, Voltage < 90 V
Top plate sensor open/short circuit Pull out the plug from the power
DANGER! Risk of injury! Before carry-
ing out any work, make sure the device is
unplugged and has cooled down fully.
NOTICE! Risk of damage to the
device! Do not use abrasive or sharp
objects or aggressive cleaning agents.
Do not use solvents.
Do not clean with oven or grill spray.
NOTICE! Risk of damage to the
device! The parts of the device are not
suitable for the dishwasher.
tened cloth.
dirt at regular intervals using a suitable, soft
brush.
DANGER! Risk of injury! Unprofes-
sional repairs may mean that your device
will no longer operate safely. This endan-
gers you and your environment.
Remedies
Contact the supplier.
Check the cable, plug, and the fuse.
Turn on the device.
Remedies
Use only cookware suitable for in-
duction with a diameter of 12-26 cm.
Place the cookware in the center of
the hotplate.
Check whether the air outlet is
blocked and whether the machine
goes back to the normal state after
cooling down. If the device is still not
working properly, contact your deal-
er.
Check whether the device is con-
nected to a properly installed power
socket.
socket and wait till the device has
cooled down. If the problem still per-
sists, please contact your dealer.
GB
25
Publicité
