Publicité
GB
– Click rocker switch to [−] position and
press [Open/Close] once, the digital screen
shows [P.0] which means power on.
– Press [Open/Close] twice, the digital screen
shows [P.1] which means first power setting.
– Press [Open/Close] 3 times, the digital screen
shows [P.2] which means second power setting.
– Press [Open/Close] 4 times, the digital screen
shows [P.3] which means third power setting.
– After the function is on, 1–24 hours timing shut-
down can be adjusted. The digital screen show-
ing [01] indicates timing one hour, [02] indicates
timing two hours, etc.
Operation of Remote Control
► P. 7, fig. 6
1. Sensor indicator. During operation, press any but-
ton and the red indicator flashes.
2. ON/OFF. Turn the device on, off, or in standby
3. First heating level. After turning on the appliance,
you can choose low heating level.
4. Second heating level. After turning on the appli-
ance, you can choose moderate heating level.
5. Third heating level. After turn on the appliance,
you can choose high heating level.
6. Timer. After the function is turned on, it can be
adjusted for 1–24 hours scheduled shutdown.
The digital screen shows that [01] means one
hour, [02] means two hours, and so on.
Note: Warning! Please insert the batteries
into the remote control.
WARNING! Risk of injury! Please use the
battery type indicated in this manual.
Improper or incorrect use of batteries may
cause corrosion or battery leakage, which
could cause personal injury or damage to
property.
Cleaning and maintenance
DANGER! Risk of injury! Always pull the
mains plug out before commencing any
work on the product.
Maintenance
Note: Attention! Infrared heaters need to be
carefully and regularly maintained to
achieve long-term efficient operation of the
equipment.
Fault/malfunction
Product does not heat
If you can't fix the fault yourself, contact your nearest
vendor. Please be aware that any improper repairs
will also invalidate the warranty and additional costs
may be incurred.
Disposal
Disposal of the appliance
A crossed-out wheelie bin icon means: Bat-
teries and rechargeable batteries, electrical
or electronic devices must not be disposed of
22
– Check the cleanliness of reflectors and infrared fil-
– Considering the amount of dust in the environ-
– When cleaning the device, visually inspect the
– Check the power cord and visually look at the plug
– It is recommended to replace the reflector every 2
Cleaning
► Cleaning – p. 7
– To be on the safe side, unplug the power cord
– Use a screwdriver to remove the front mesh from
– For your safety, make sure the power is turned off.
– Reflectors and filaments must be cleaned with a
– Avoid using cleaning materials (detergents, etc.)
– Use a screwdriver to insert the grid.
Troubleshooting
If something stops working...
Malfunctions are often caused by minor faults. You
can easily remedy most of these yourself. Please
consult the following table before contacting the ven-
dor. You will save yourself a lot of trouble and possibly
money too.
Cause
Is the product switched off?
No mains voltage?
with household waste. They may contain substances
that are harmful to the environment and human
health.
Consumers must dispose of waste electrical devices,
spent portable batteries and rechargeable batteries
separately from household waste at an official collec-
tion point to ensure that these items are processed
correctly. The product can be returned free of charge
in accordance with the legal requirements, for exam-
ple through a municipal waste disposal company or a
dealer.
aments at least once a month.
ment, the number of inspections may increase.
deformation of reflectors, wires and frames. If any
deformation occurs, consult a qualified techni-
cian.
when cleaning the appliance. If any deformation
occurs, consult a qualified technician.
years to improve operational efficiency.
Note: Attention! Regular and careful clean-
ing can help your heater run longer and
more efficiently.
before cleaning the device.
the inlet on the frame
The power cord plug must be unplugged.
soft cloth, smooth brush. The cloth can be damp,
but not too wet, and the cleaner should not con-
tain any chemicals.
that may damage the reflector.
DANGER! Risk of injury! Improper repairs
can result in the product functioning
unsafely. This endangers yourself and your
environment.
Remedy
Set the desired heat level.
Check cable, plug, socket and fuse.
Publicité
