Publicité
Liens rapides
H-2901, H-2902, H-2903
H-2904, H-2905, H-2906
H-2907, H-2908, H-5435
SLIDING STORAGE
SHELVES
TOOL NEEDED
Rubber Mallet
(optional)
In addition to the posts, shelves, levelers and shelf supports from the
Adjustable Open Wire Shelving, this kit includes the following:
Middle Track x 2-6
SHELVING UNIT
1.
Unscrew and remove the
bolts from the post inserts.
(See Figure 1)
2. Make sure post is positioned as shown. (See Figure 2)
3. Use a rubber mallet/hammer or tap on ground until
post inserts slide into posts. (See Figure 2)
Figure 2
PAGE 1 OF 9
1-800-295-5510
uline.com
PARTS
End Track x 4
Stop x 4
Adjustable Pin x 6-10
ASSEMBLY
Figure 1
Bolt x 8
4. Start with the lowest shelf. Snap the interlocking
pieces of a shelf support (wide end down) around
the post at the lowest groove where shelf is to be
located. Slide the support up or down until it snaps
into the groove. Add a shelf support to the same
place on the remaining posts. (See Figure 3)
NOTE: NSF requires food service applications to
keep the lowest shelf at least 6" above the floor.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
Allen Key x 1
Roller Assembly x 6-10
Figure 3
1224 IH-2901
Publicité
Manuels Connexes pour Uline H-2901
Sommaire des Matières pour Uline H-2901
- Page 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. H-2901, H-2902, H-2903 H-2904, H-2905, H-2906 1-800-295-5510 H-2907, H-2908, H-5435 uline.com SLIDING STORAGE SHELVES TOOL NEEDED Rubber Mallet (optional) PARTS In addition to the posts, shelves, levelers and shelf supports from the...
- Page 2 ASSEMBLY CONTINUED SLIDING TRACK 5. Slide posts through underside of shelf until shelf slides firmly over supports. (See Figure 4) 1. Attach stops to the ends of the tracks using two bolts. (See Figure 7) Figure 4 Figure 7 6. Stand unit upright. Gently tap shelf down to secure it. (See Figure 5) 2.
- Page 3 5. Carefully place the shelving units on the pins of the roller assemblies. Pins should fit inside the inserts in NOTE: Roller brake should face outwards. the bottoms of the posts. (See Figure 11) Figure 10 Figure 11 1-800-295-5510 uline.com PAGE 3 OF 9 1224 IH-2901...
- Page 4 H-2901, H-2902, H-2903 H-2904, H-2905, H-2906 800-295-5510 H-2907, H-2908, H-5435 uline.mx ESTANTERÍA CORREDIZA PARA ALMACENAMIENTO HERRAMIENTA NECESARIA Mazo de Hule (opcional) PARTES Además de los postes repisas, niveladores y soportes para repisas de la Estantería de Alambre Ajustable, este kit incluye lo siguiente:...
- Page 5 CONTINUACIÓN DE ENSAMBLE RIEL CORREDIZO 5. Deslice el poste a través del lado inferior de la repisa hasta que se ajuste con firmeza sobre los Fije los topes a los extremos de los rieles usando dos soportes. (Vea Diagrama 4) pernos.
- Page 6 Los pasadores se deben ajustar en los NOTA: El freno del rodillo debería mirar hacia insertos ubicados en la parte inferior de los postes. fuera. (Vea Diagrama 11) Diagrama 10 Diagrama 11 800-295-5510 uline.mx PAGE 6 OF 9 1224 IH-2901...
- Page 7 H-2901, H-2902, H-2903 H-2904, H-2905, H-2906 1 800 295-5510 H-2907, H-2908, H-5435 uline.ca ÉTAGÈRES DE RANGEMENT COULISSANTES OUTIL REQUIS Maillet en caoutchouc (optionnel) PIÈCES En plus des montants, des tablettes, des patins réglables et des supports de tablette fournis avec le rayonnage réglable espacé...
- Page 8 MONTAGE SUITE RAIL COULISSANT 5. Insérez les montants par le dessous de la tablette Fixez les butées aux extrémités des rails à l'aide de jusqu'à ce que la tablette repose fermement sur les deux boulons. (Voir Figure 7) supports. (Voir Figure 4) Figure 7 Figure 4 2.
- Page 9 Les tiges doivent s'insérer à l'intérieur des embouts au bas des montants. REMARQUE : Le frein du dispositif de roulement (Voir Figure 11) doit être orienté vers l'extérieur. Figure 10 Figure 11 1 800 295-5510 uline.ca PAGE 9 OF 9 1224 IH-2901...