Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
H-6922, H-6923
H-6924
STAINLESS STEEL
UTILITY STAND
TOOL NEEDED
5/32" Allen Wrench
(included)
Tabletop x 1
Undershelf x 1
PAGE 1 OF 9
1-800-295-5510
uline.com
PARTS
Legs with Adjustable Feet x 4
ASSEMBLY
1.
Figure 1
Pour le français, consulter les pages 7-9.
NOTE: If purchased with optional casters,
adjustable feet will be replaced after complete
table assembly.
With the undershelf on its side, push the legs through
the collars to the desired height. To ensure exact
height, mark desired height on each leg with magic
marker or grease pencil. (See Figure 1)
NOTE: Each leg must be at the same height or
shelf collars could fail. Recommended height
from the floor to the top of the undershelf is 10"
and must be 6" or higher to meet NSF standards.
NOTE: Optional casters add 3⁄" to height.
Para Español, vea páginas 4-6.
Set Screw x 16
Caster x 4
(Optional)
0721 IH-6922
Publicité
Manuels Connexes pour Uline H-6922
Sommaire des Matières pour Uline H-6922
- Page 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. H-6922, H-6923 1-800-295-5510 H-6924 uline.com STAINLESS STEEL UTILITY STAND TOOL NEEDED 5/32" Allen Wrench (included) PARTS Set Screw x 16 Tabletop x 1 Legs with Adjustable Feet x 4...
- Page 2 ASSEMBLY CONTINUED 2. Secure legs to undershelf with set screws using 5/32" Allen wrench. (See Figure 2) NOTE: Undershelf must be level. Use care not to overtighten screws or failure will occur. Figure 2 3. Stand table upright and place tabletop onto legs, inserting legs into tabletop gussets.
- Page 3 4. With caster fully inserted into the leg, turn clockwise Figure 8 until caster is secured to tube leg. (See Figure 8) NOTE: If too loose, pull out caster and tighten further. Repeat step 2. Tube Leg 1-800-295-5510 uline.com PAGE 3 OF 9 0721 IH-6922...
- Page 4 H-6922, H-6923 800-295-5510 H-6924 uline.mx MESA DE TRABAJO DE ACERO INOXIDABLE HERRAMIENTA NECESARIA Llave Allen de 5/32" (incluida) PARTES 16 Tornillos de Sujeción 1 Cubierta 4 Patas Ajustables 1 Repisa Inferior 4 Ruedas (Opcionales) ENSAMBLE NOTA: Si se adquiere con ruedas opcionales, las patas ajustables se reemplazarán después...
- Page 5 CONTINUACIÓN DE ENSAMBLE 2. Asegure las patas a la repisa inferior con los tornillos de sujeción utilizando una llave Allen de 5/32". (Vea Diagrama 2) NOTA: La repisa inferior debe estar nivelada. Tenga cuidado de no apretar los tornillos de más o de lo contrario puede averiarse.
- Page 6 (Vea Diagrama 8) NOTA: Si queda muy floja, saque la rueda y apriete más. Repita el paso 2. Pata del Tubo 800-295-5510 uline.mx PAGE 6 OF 9 0721 IH-6922...
- Page 7 H-6922, H-6923 1-800-295-5510 H-6924 uline.ca TABLE UTILITAIRE EN ACIER INOXYDABLE OUTIL REQUIS Clé Allen de 5/32 po (incluse) PIÈCES Vis de réglage x 16 Surface de table x 1 Pieds avec pattes réglables x 4 Tablette inférieure x 1 Roulette x 4...
- Page 8 MONTAGE SUITE 2. Fixez les pieds à la tablette inférieure à l'aide des vis de réglage et de la clé Allen de 5/32 po. (Voir Figure 2) REMARQUE : La tablette inférieure doit être nivelée. Faites attention de ne pas trop serrer les vis ou une défaillance se produira.
- Page 9 (Voir Figure 8) REMARQUE : Si la roulette est trop lâche, retirez- la et serrez davantage. Répétez l’étape 2. Tube de pied 1-800-295-5510 uline.ca PAGE 9 OF 9 0721 IH-6922...