Publicité
SETTING UP YOUR ESPRESSO MAKER
WARNING - If the hot water/steam selector dial is in the
when you press the button, the
will beep 3 times. Immediately turn the dial to STANDBY to prevent hot
water/steam being released during preheating.
4. While in ready/standby mode, the boiler will remain heated to the preset temperature for
brewing co ee. If there is no operation in 30 minutes, the espresso machine will return to POWER
OFF status. The
indicator remains faintly lit at all times when the machine is plugged in.
DISPENSING HOT WATER
To dispense hot water from the hot water outlet, turn the steam/hot water dial from STANDBY to
the
position. The
indicator will ash white and hot water will run out of the tap until you
return the dial to STANDBY.
NOTE - As a safety measure, after 90 seconds of continuous operation, the hot water will stop
automatically. The
will stay solidly white and the machine will beep continuously to remind you
to return the dial to STANDBY.
WARNING - Use extreme caution when dispensing hot water!
To prevent burns or scalds, avoid contact with the hot water tap.
FLUSHING THE SYSTEM
"Flushing the system" means running hot water and steam through the various parts of your
machine without ground co ee. Regularly ushing the system will help keep your machine in the
best possible condition. It is especially important before using the machine for the rst time or
after a period of disuse.
1. Fill the water tank to the MAX marking and preheat
the machine to ready/standby mode.
2. Press the 2-cup/ double shot
button to run hot
water through the group head into the drip tray, milk
pitcher, or an empty heat-safe cup. Repeat 1-2 more
times.
3. Position the steam wand over the drip tray (Figure
2), milk steaming pitcher, or an empty heat-safe cup
and turn the steam/hot water dial to the
The machine will beep once and the
ash alternately red and white as the boiler preheats
to steaming temperature (10-15 seconds) .
or
indicator will ash red, and the machine
Fig. 2
position.
indicator will
10
SETTING UP YOUR ESPRESSO MAKER
position
4. When preheating is complete the machine will beep once, the indicator will switch to ashing
white only, and the wand will start to release steam. Run steam through the wand for 10 seconds
and then return the dial to the STANDBY position to stop.
5. Turn the dial to the
heat-safe cup, or the drip tray for about 10 seconds, then return the dial to STANDBY.
6. Repeat steps 2-5 until the water tank is empty, checking the drip tray or cup after each step and
emptying as needed to prevent over owing. The orange "tray full" indicator will pop up to let you
know when the drip tray needs to be emptied.
COOLING DOWN
When you turn the steam/hot water dial from
ing steam and the
to resume steaming or press the
further operation within 30 seconds, the cooling process will start automatically.
During the cooling process, you will hear pumping sounds and the
ly red and white. When the boiler reaches the correct temperature for brewing co ee, the
machine will beep once and return to ready/standby mode.
WARNING - Although these instructions say "cooling," your machine
is still very hot! Be very careful not to touch any of the heated surfaces.
WARNING - The steam wand may release hot water and/or steam
during preheating. Be sure the steam wand is properly positioned
before preheating and keep body parts clear of the tip.
WARNING -The steam wand gets very hot. Always use the safe-
to-touch grip to move it and avoid touching the bare metal.
position to run hot water into the milk steaming pitcher, an empty
WARNING - Check and empty the drip tray regularly to prevent
over owing. Use extreme caution when emptying as the metal
tray cover and water will be very hot.
back to STANDBY, the machine will stop dispens-
and
indicators will light up solidly white. You can turn the dial back to
button to start the boiler cooling down. If there is no
11
indicator will ash alternate-
Publicité
