Publicité
DIGITAL RADIO CONTROL SYSTEM TVPRD868A01T
UK
ATTENTION!
The subject appliance must be installed only by qualified technical
personnel in compliance with the standards. All connections must be
rated for a single-phase power supply of 230V. For the disconnection from
the power line, use an all-pole switch with contact with an opening of at
least 3,5mm. Only suitable materials for the connections must be used to
guarantee insulation that complies with current standards on the subject
of electrical safety. The programmer carries out movement commands by
radio; all the necessary safety devices are to be seen to separately.
The device's signal reception could be disturbed by several factors such as:
- the presence of electrical frequency noise being transmitted by other
appliances working in the same environment and on the same frequency.
- appliances installed in containers with metal parts; only use containers made
of plastic.
1- GENERAL DESCRIPTION
Electronic device for the remote control of tubular motors for rolling shutters
with mechanical and electronical travel limits incorporated in the motor.
Input for dynamic push button.
Execution with ABS V0 plastic container to be integrated inside electric
junction boxes. Single or centralised commands for the simultaneous control of
several appliances. The work cycle time is fixed at 90 sec.
The specific TVLINK codes are encoded directly by the manufacturer inside
an EEprom memory module that maintains the information even in case of
blackouts. They are also printed on the product label so they can be inserted into
the TVLINK device. These codes cannot be cancelled or modified as they are an
integral part of the receiver.
The standard radio control codes can be inserted (memorized) or cancelled in
the receiver by pressing a button (P1) through a small hole located to one side
of the aerial.
The code transmission type is "Rolling-code". The code is changed for every
transmission through the use of an algorithm that only the receiver is able to
recognize.
The maximum number of memorisations that can be executed is 83.
2- Transmitters
The transmitters are encoded in the factory and each transmitter has its own
unique code.
Caution! If you keep a channel button pressed down for more than 30 seconds
the transmitter will automatically switch off.
The receiver is compatible with all transmitters of the TVLink range: TVTXV,
TVTXP, TVTXC, TVTXK, TVTXQ, TVTXL, TVTXS.
Channels function:
CH1: open/stop
CH2: close/stop
CH3: open/stop
CH4: close/stop
CH5: open
CH6: stop
CH7: close
Attention: The first memorised channel determines the rotation sense of the
motor. If the motor is installed on the right, memorise CH1, if the motor is
installed on the left, memorise CH2 (in case of error cancel the channel and
rememorize with the opposite channel) (the rotation sense is determined by
the first channel which is inserted with empty memory).
The insertion of the first channel determines the association opening/closing
of the other transmitters which are memorised afterwards.
3- Memorisation
Each time you start a new installation you should cancel the entire memory.
3.1- Memorisation from the transmitter
The channels ch1,ch2 and ch3,ch4 will be memorised in couple.
1) Press P3 of the transmitter, the buzzer will sound continuously for 5 s.
2) press one of the couple of channel which is to be memorized within 5
seconds and once memorized the buzzer will sound intermittently.
See paragraph 4 to memorise ulterior channels from transmitter.
3.2- Memorisation from the receiver
The channels ch1,ch2 and ch3,ch4 will be memorised in couple.
1- Press and hold down the pushbutton P1 of the receiver, the buzzer will sound
continuously.
2- Press one of the couple of channel which is to be memorized, once the
channel is memorised, the buzzer will sound intermittently, release the
pushbutton.
Repeat points 1 and 2 to memorize ulterior channels from receiver.
See paragraph 4 to memorize ulterior couple of channels from transmitter.
Code Number:
TVPRD868A01T
TELECO AUTOMATION SRL -
++39.0438.388511 FAX: ++39.0438.388536
TELEPHONE:
This document is the property of Teleco Automation Srl who reserves all reproduction and copying rights
Series
TVLink RS868
Viale del Lavoro, 5 - 31014 Colle Umberto (TV) ITALY
4- How to insert a transmitter via radio without having to access the
receiver by means of an already memorized transmitter (memory indexing
procedure)
1) Press the button P3 located inside the already memorized transmitter. The
receiver sound continuously for 5 seconds.
2) press a channel present in the memory of the receiver, in which the new code
is to be memorized, within 5 seconds and the buzzer will interrupt the sound for
1 sec, and then carry on for another 5 seconds.
3) press one of the couple of channel which is to be memorized within 5
seconds and once memorized the buzzer will sound intermittently.
To insert other couple of channels repeat operations 1,2 and 3
5- To cancel a couple of channels from the receiver:
1) Press two times and then hold down the button P1 and the buzzer will sound
intermittently and slowly.
2) press the channel which is to be cancelled, once the channel has been
cancelled the buzzer will stop sounding.
To cancel other couple of channels repeat operations 1 and 2.
5.1- To cancel a couple of channels from via radio:
1) Press three times and hold down the button P3 within 5 seconds and the
buzzer will sound intermittently and slowly.
2) press one of the couple of channel which is to be cancelled, once the channel
has been cancelled the buzzer will stop sounding.To cancel other couple of
channels repeat operations 1 and 2.
5.2- To cancel all codes in memory:
1) Press the button P1 three times and hold down for at least 10 seconds (during
this period the buzzer will sound intermittently and rapidly) until the buzzer will
sound continuously. Release the button.
6- Full or empty memory
If the memory of the receiver is full, the buzzer will make 3 bip during the
memorisation.
6.1- Errors during the memorising or deleting
If the code hasn't been memorised it could be due to the following reasons:
- the memory is full. In this case the buzzer will sound intermittently and slowly
for 3 seconds each time it is switched on,
- the indexing procedure has not been correctly started up,
- the code already exists in memory.
If the code hasn't been cancelled it could be due to the following reasons:
- the code doesn't exist in memory.
7- TECHNICAL SPECIFICATIONS
Reception frequency
Intermediate frequency
Sensitivity (finely tuned signal)
Power supply
Maximum commutable power at the relay:
Voltage
Current with cos ph1 (with resistive load)
Current with cos ph0,4 (with inductive load) 2A
Operating temperature range
In the view of a constant development of their products, the manufacturer
reserves the right for changing technical data and features without prior notice.
Model number
3
868.3 MHz
10.7MHz
1 µV
230 V
250V
5A
-20° ÷ + 60 °C
Draft
Date
Publicité
