Publicité
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR CIRCULAR SAWS
DANGER
•
Keep hands away from cutting area and the
blade; keep your second hand on front handle
(if both hands are holding the saw, they can not be cut
by the blade)
• Do not reach underneath the workpiece (the guard
cannot protect you from the blade below the workpiece)
• Adjust the cutting depth to the thickness of the
workpiece (less than a full tooth of the blade teeth
should be visible below the workpiece)
• Never hold piece being cut in your hands or across
your leg (it is important to support the work properly to
minimise body exposure, blade binding, or loss of
control)
• Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord (contact with a
"live" wire will also make exposed metal parts of the
tool "live" and shock the operator)
• When ripping always use a rip fence or straight edge
guide (this improves the accuracy of cut and reduces
the chance for blade binding)
• Always use blades with correct size and shape of
arbor holes (diamond or round) (blades that do not
match the mounting hardware of the saw will run
eccentrically, causing loss of control)
• Never use damaged or incorrect blade washers or
bolts (the blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation)
KICKBACK - CAUSES
• Kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw to
lift up and out of the workpiece toward the operator
• When the blade is pinched or bound tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator
• If the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the
top surface of the wood causing the blade to climb out
of the kerf and jump back towards operator
KICKBACK - OPERATOR PREVENTION
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below
• Maintain a firm grip with both hands on the saw and
position your arms to resist kickback forces;
position your body to either side of the blade, but
not in line with the blade (kickback could cause the
saw to jump backwards, but kickback forces can be
controlled by the operator, if proper precautions are
taken)
• When blade is binding, or when interrupting a cut for
any reason, release the trigger and hold the saw
motionless in the material until the blade comes to a
complete stop; never attempt to remove the saw
from the work or pull the saw backwards while the
blade is in motion or kickback may occur (investigate
and take corrective actions to eliminate the cause of
blade binding; avoid cutting nails or screws)
• When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are
not engaged into the material (if saw blade is binding,
it may walk up or kickback from the workpiece as the
saw is restarted)
• Support large panels to minimise the risk of blade
pinching and kickback (large panels tend to sag under
their own weight; supports must be placed under the
panel on both sides, near the line of cut and near the
edge of the panel)
• Do not use a dull or damaged blade (unsharpened or
improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback)
• Blade depth and bevel adjusting locking levers must
be tight and secure before making cut (if blade
adjustment shifts while cutting, it may cause binding
and kickback)
• Use extra caution when making a plunge cut into
existing walls or other blind areas (the protruding
blade may cut objects that can cause kickback)
WARNING
• Check lower guard for proper closing before each
use
• Do not operate the saw if lower guard does not
move freely and close instantly
• Never clamp or tie the lower guard into the open
position
• If saw is accidentally dropped, lower guard may be
bent; disconnect the plug, raise the lower guard with
the retracting handle and make sure it moves freely and
does not touch the blade or any other part, in all angles
and depths of cut
8
Publicité
