Publicité
For tool with the lock-on switch
Country specific
For continuous operation, pull the switch trigger and
then push in the lock button. To stop the tool from the
locked position, pull the switch trigger fully, then release
it.
► Fig.1: 1. Switch trigger 2. Lock button (Country
specific)
Hook
Optional accessory
CAUTION:
Always be sure that the tool is
switched off and unplugged when hanging the
tool.
CAUTION:
Never hang the tool at high or
potentially unstable location.
CAUTION:
Do not hook the tool on your belt
or other accessories. The recipro saw blade may
contact your body and cause personal injury.
The hook is convenient for hanging the tool temporarily.
To use the hook, simply lift up hook until it snaps into
the open position.
When not in use, always lower hook until it snaps into
the closed position.
► Fig.2: 1. Hook
Attach the hook by following procedure.
1.
Insert the tip of slotted screwdriver into the notch
and remove the the cover by pressing and sliding
it.
► Fig.3: 1. Notch 2. Cover
2.
Insert the square nuts into the tool as shown in the
figure.
3.
Secure the hook with the screws.
► Fig.4: 1. Square nut 2. Hook 3. Screw
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and unplugged before carrying out
any work on the tool.
Installing or removing the recipro
saw blade
CAUTION:
Always clean out all chips or for-
eign matter adhering to the blade and around the
blade clamp. Failure to do so may cause insufficient
tightening of the blade, resulting in a serious injury.
Before installing the recipro saw blade, always make
sure that the blade clamp lever (part of the blade clamp
sleeve) is in released position
cover. If the blade clamp lever is in fixed position, rotate
the blade clamp lever in the direction of the arrow so
that it can be locked at the released position
► Fig.5: 1. Blade clamp lever 2. Released position
on the insulation
.
6 ENGLISH
3. Fixed position
Insert the recipro saw blade into the blade clamp as far
as it will go. The blade clamp sleeve rotates and fixes
the recipro saw blade. Make sure that the recipro saw
blade cannot be extracted even though you try to pull
it out.
► Fig.6: 1. Recipro saw blade 2. Blade clamp sleeve
CAUTION:
If you do not insert the recipro saw
blade deep enough, the recipro saw blade may be
ejected unexpectedly during operation. This can
be extremely dangerous.
To remove the recipro saw blade, rotate the blade
clamp lever in the direction of the arrow fully. The reci-
pro saw blade is removed and the blade clamp lever is
fixed at the released position
► Fig.7: 1. Recipro saw blade 2. Blade clamp lever
CAUTION:
Keep hands and fingers away from
the lever during the switching operation. Failure
to do so may cause personal injuries.
NOTE: If you remove the recipro saw blade without
rotating the blade clamp lever fully, the lever may not
be locked in the released position
rotate the blade clamp lever fully again, then make
sure that the blade clamp lever locked at the released
position
.
NOTE: If the blade clamp lever is positioned inside
the tool, switch on the tool just a second to let the
blade out. Unplug the tool before installing or remov-
ing the recipro saw blade.
OPERATION
CAUTION:
Always hold the tool firmly with
one hand on insulation cover and the other on the
switch handle.
CAUTION:
Always press the shoe firmly
against the workpiece during operation. If the
shoe is removed or held away from the workpiece
during operation, strong vibration and/or twisting will
be produced, causing the blade to snap dangerously.
CAUTION:
Always wear gloves to protect
your hands from hot flying chips when cutting
metal.
CAUTION:
Be sure to always wear suitable
eye protection which complies with current
national standards.
CAUTION:
Always use a suitable coolant
(cutting oil) when cutting metal. Failure to do so will
cause premature blade wear.
CAUTION:
Do not quirk the blade during
cutting.
Press the shoe firmly against the workpiece. Do not
allow the tool to bounce. Bring the recipro saw blade
into light contact with the workpiece. First, make a pilot
groove using a slower speed. Then use a faster speed
.
. In this case,
Publicité
