Ac Power Cord; Display Lcd; Disc Drawer - NAD L 40 Manuel D'installation

GB
To function with other units, connect the L 40's
NAD-LINK OUT to the NAD-LINK IN on the other
unit. NAD-LINK connectors can be daisy-chained, IN
to OUT, so that a whole system can be controlled
from the remote control facilities of one unit.

7. AC POWER CORD

Connect the AC Power cord to a suitable AC outlet
socket.
FRONT PANEL CONTROL
1. POWER
Press the POWER button to switch unit ON. The
display and volume control LED will illuminate.
Pressing the POWER switch again will turn the unit
OFF completely. The L 40 uses a memory back-up
system to store preset station information for the
tuner. This information is retained for several weeks,
even the unit is switched off completely or unplugged.
REMOTE CONTROL:
STAND-BY button (green):
Press this button to switch the unit from operating
to the Stand-by mode and vice versa: Press this but-
ton again to switch the unit on from Stand-by.
NOTE:
Stand-by mode is indicated by the amber light just
over the green POWER button on the front panel (No. 1)
In Stand-by mode, the L 40 uses very little power.
However, it is recommended that you switch the unit
totally off if it is not going to be used for more than a
couple of days. Switch off completely by pressing the
POWER button on the front panel (No. 1), all lights
will extinguish.
2. PHONES
A 1/4" stereo jack socket is supplied for headphone
listening and will work with conventional headphones
of any impedance. Inserting a headphone jack into
this socket automatically switches off the loudspeak-
ers. The volume, tone and balance controls are oper-
ative for headphones listening. Use a suitable
adapter to connect headphones with other types of
connectors, which have 3.5mm stereo 'personal
stereo' jack plug.
NOTE:
Make sure the volume control is turned to minimum
(fully anti-clockwise) before connecting headphones.
Listening at high levels can damage your hearing.

3. DISC DRAWER

To load a disc, press the STOP/OPEN (No. 5) but-
ton to open the disc drawer. Place the CD within the
large circular recess in the drawer, with its transpar-
ent playing surface facing down. The label must face
up.
NAD
6
Press OPEN again to close the drawer or press
PLAY/PAUSE to close the drawer and start playback.
CD-3 discs (3-inch CD 'singles') can be played
without the aid of an adapter. Place the disc in the
drawer, centred in the smaller circular recess, with its
label facing up.
NOTE:
This player is not designed to accommodate a
'damping disc' placed on a CD, nor two CDs stacked
together. It plays audio CDs, but not discs identified
as CD-V, DVD, CD-I, CD-ROM, or PHOTO CD.
4. DISPLAY (LCD)
The LCD display provides information on the
selected input and status of the CD and Tuner.
IN CD MODE:
TRACK NUMBER. Each disc is segmented into
numbered tracks when the recording is made; typical-
ly each numbered track will correspond to a different
song, symphonic movement, etc.
These track numbers are identified on the CD
package and are encoded in the disc by its manufac-
turer.
Normally the alpha-numeric section of the display
shows the time elapsed since the beginning of the
current track. Using the DISPLAY button (No. 14) you
can switch the display to show the playing time
remaining to the end of the disc.
A right-pointing arrowhead
left edge of the display, lights up during play. Two
vertical bars indicate that the player is in pause.
In stop mode the display reverts to showing the
number of tracks and total playing time of the disc.
"NO DISC" is indicated in the display when there
is no disc in the drawer or when you load a disc that
cannot be read (because it is dirty or is upside-down).
"REPEAT 1" lights up in the upper-left corner dur-
ing repeat-play of a single track.
"REPEAT ALL" lights up during repeat play of the
entire CD or all pre-programmed tracks.
Both "REPEAT 1" and "REPEAT ALL" can be
engaged by pressing button No. 9.
"TOTAL REMAIN" lights up in the centre area of
the display if you have pressed the DISPLAY button
to show the remaining time in the disc.
"RANDOM." When the L 40 is in random mode
"RANDOM" will be shown in the display panel.
, located near the