Utilisation; Electrical Safety - Husqvarna TS 230 F Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
This symbol indicates that the
machine is in conformance with
the applicable European directive.
MANDATORY
WARNING
These signs give advice
concerning your safety
Instruction plate
MANUFACTURER
TYPE
TYPE
N° SERIE
ANNEE DE
FABRICATION
WEIGHT
MASSE UTILE
Kg
PUISSANCE
PLAGE DE
MAXI TOOL
Ø MAXI OUTIL.
mm
TENSION
BORE
Ø ALESAGE
mm
FREQUENCE
SPEED
T/MN - RPM
INT. UTIL.
1

Utilisation

• Utilisation : Water-cooled cutting of tile
materials.
• Blade with continuous rim Ø 230 mm (D)
bore Ø x25.4 mm (AL).
Use only continuous rim diamand
blades.
• Cutting thickness (material) :
to 90° : 48 mm - to 45° : 37 mm
• Cutting width (Lg) with guide at 90° :
305 mm to the left
147 mm to the right
• Length of cut unlimited.
3
Pre-use check-list
Before use, read the instructions
INDICATION
carefully and familiarise yourself
INFORMATION
with the machine.
INSTRUCTION
The working area must be per-
PROHIBITION
fectly tidy, well lit and must offer
no risks (no humidity or dange-
rous products in the vicinity).
SERIAL
FABRICATION
YEAR
Any unauthorised persons must
kW
POWER
be kept away from the working
V
VOLTAGE
FREQUENCY
area.
Hz
A
INTENSITY
Use blades suitable for the work
to be done (speed, geometry,
application, etc.)
4
Electrical connections

- ELECTRICAL SAFETY :

Operate this machine only on a
supply equipped with a 30 mA ear-
thed current-limiting circuit-brea-
ker. Otherwise, consult our catalo-
gue for appropriate models.
- The RCCB must be used cor-
rectly, including testing it regu-
larly. For tools supplied with an
integral RCCB in the cable or in
the mains plug, if the cable or
plug
repairs must be carried out by
the manufacturer, one of his
agents or by a qualified repair
workshop to avoid any risks
resulting from errors.
- Check the mains voltage is iden-
tical to that shown on the instruc-
tion plate N on the machine
[FIG. x1]
- Use twin & earth plugs S.T.D. 3
pin plug 240 V.
- Extension cable : cable section
adequate for the electric power,
connection to the main by a type
HO7 RNF cable of 2.5 mm
tion up to 50 m.
The operator must wear
suitable protection when
working.
has
been
damaged,
sec-
2
5
Fitting the blade
• Unplug the machine.
• Remove the housing from the disk
• Remove the table by pulling on the levers
(figs. 2 and 3).
• Remove the motor clamp screw, right-
hand thread.
• Remove the pressure disk.
• O er up the diamond cutting blade.
Rotation direction is indicated by
an arrow on one side of the
blade.
Make sure the contact faces of
flanges, of blade and the axle are
clean
• Check correct centring of the blade.
• Replace the outer ange and lock the nut.
• Replace the table
• Replace the disk housing
6
Starting up
Always take care.
Get into a comfortable, balanced
position.
Remove all adjustment tools and
wrenches from floor and machi-
ne
Keep the protective covers in
place while the machine is opera-
ting.
• Fill the water bath.
• Connect the machine to the mains.
• Start by means of the on-o switch
(fig 1).
I
.
11

Publicité

Table des Matières
loading

Table des Matières