Publicité
Liens rapides
`
Part No.
21020X, 21022X, 21024X
Do not over tighten as screws can be stripped out.
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
DO NOT OVER TORQUE. STANDARD OPERATING LOAD FOR TIGHTEN
BODY MOUNT NUTS & BOLTS VARIES FROM 45 TO 65 FOOT POUND.
1/2" Socket Wrench,
Phillips Driver.
1. INSTALLATION PROCEDURE:
WARNING:
Do not transport a pickup truck facing backward with a liner installed.
Air can get under the liner which may result in the liner coming out of the truck and causing damage or injury.
Truck Box Preparation:
Clean truck box of all foreign matter and open any floor drains to ensure ventilation and moisture drainage.
NOTE:
Bed liner can be installed by one person. However, using two people is recommended by the manufacturer.
2. Tailgate Cover Installation Steps
Page 1 of 7
GM UNDERRAIL BEDLINER/TAILGATE
COVER
Tools Required
30-60 min
support@trailfx.com
1 866 638 4870
Limited Lifetime
#20 Torx driver,
Electric Drill,
STEP 1
Remove the 2 existing factory installed screws from tailgate
latch plate.
STEP 2
Center plastic tailgate cover on truck tailgate. Insert and
tighten the two screws in the two center holes of tailgate.
STEP 3
Center a self-drilling screw in a pre-drilled hole in the tailgate
cover. Fasten the screw to the tailgate with a power
screwdriver (see Figure 1).
Do not over tighten because the screw threads can be
Stripped easily.
STEP 4
Repeat Step 3 to remaining hole locations until all are
completed.
www.TrailFX.com
CUTTING NOT
DRILLING
REQUIRED
REQUIRED
Rev 062816
Publicité
Manuels Connexes pour Trailfx 21020X
Sommaire des Matières pour Trailfx 21020X
- Page 1 GM UNDERRAIL BEDLINER/TAILGATE COVER Part No. 21020X, 21022X, 21024X Do not over tighten as screws can be stripped out. CUTTING NOT DRILLING 30-60 min REQUIRED REQUIRED REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. support@trailfx.com READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- Page 2 3. Bedliner Installation Steps For Trucks without Cargo Management Rails STEP 1 Place bedliner in truck box. While standing beside truck at approximately the center of box area, lift side of bedliner up at a 450 angle so that the opposite side slips under the siderail of pickup truck (See FIGURE 1).
- Page 3 COUVERTURE DU GM UNDERRAIL BEDLINER/TAILGATE Part No. 21020X, 21022X, 21024X Outils nécessaires Mandrin Torx n° 20 Clé à douille de 12,7 mm (1/2 po), Tournevis à pointe cruciforme. Perceuse électrique, 1. Préparation pour installation AVERTISSEMENT: Ne transportez pas, dans le sens contraire de la marche, un camion équipé d’une doublure de caisse.
- Page 4 3. Doublure de caisse à poser sous les longerons Camions sans glissières de gestion des bagages ÉTAPE 1 Placer la doublure dans la caisse du camion. En se tenant debout à côté du camion, environ au centre de la caisse, soulever le côté...
- Page 5 MONTAJE EN CAMIONETA GM DEL BEDLINER POR DEBAJO DE LA BARANDA Y DE LA CUBIERTA DE LA COMPUERTA Part No. 21020X, 21022X, 21024X Herramientas necesarias: Destornillador Torx No. 20 Llave de copa de 1/2", Destornillador Phillips. Taladro eléctrico 1. Preparación para la instalación: ADVERTENCIA: ...
- Page 6 Pasos de la instalación Bedliner Para los pickups sin rieles de manejo de carga PASO 1 Coloque el protector en la caja de carga del pickup. Mientras esté junto al pickup aproximadamente en el centro del área de la caja de carga, levante la parte lateral del protector de la caja de carga en un ángulo de 45 grados a fin de que el lado...
- Page 7 Product not installing properly. Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly. Check out these other TrailFX Products!! www.TrailFX.com Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of purchase by the original retail consumer.