Publicité
¡ Connect the appliance to a fixed gas pipe or a
flexible metal pipe.
¡ The flexible metal pipe must not come into contact
with the moving parts of the unit in which the ap-
pliance is installed (e.g. a drawer) and must not
be routed through any spaces which might be-
come obstructed.
¡ Gas connection elbow on the appliance: R 1/2.
¡ Do not move or twist the gas connection elbow.
Spare parts for gas connection
You can obtain the gas connection parts from the
technical customer service.
Seal
Gas connection elbow: G 1/2
Gas connection R 1/2
→ Fig.
9
Gas connection G 1/2
Replace the gas connection elbow on the appli-
1.
ance with the gas connection elbow G 1/2 sup-
plied in the accessory bag.
→ Fig.
10
Insert the seal between the gas connection of the
2.
appliance and the gas supply.
→ Fig.
11
Electrical connection
¡ This appliance is type Y: The connection cable
must only be replaced by technical customer ser-
vice and not by the user. The cable type and the
minimum cross section must be respected.
¡ The hobs are supplied with a power cord with or
without a plug.
¡ Only connect appliances that are fitted with a plug
to a correctly installed socket with protective earth
conductor.
¡ If the plug is not accessible to the user, an all-pole
isolating safety switch with a minimum contact
opening of 3 mm must be provided.
→ Fig.
12
Converting the gas type
If the country's regulations allow, this appliance can
be adapted to other types of gas, if these are listed
on the rating plate.
You can find the right parts in the bag that is sup-
plied with the appliance or you can obtain them from
customer service. The table → Fig.
right combination for the relevant burner and gas
type.
Economy burner
Standard-output burner
High-output burner
Adjusting the taps
Turn the rotary knobs to the minimum power posi-
1.
tion and pull them out.
With the tip of the screwdriver, push down on the
2.
flexible rubber holder to access the bypass screw.
→ Fig.
13
Never remove the sealing ring. The sealing rings
prevent liquids and dirt from finding their way into
the appliance and impairing its ability to function
properly.
3.
Replacing the nozzles
1.
2.
00034308
10006024
Reinstalling the appliance
▶
Checking if equipment is working
1.
2.
Documenting the gas type conversion
▶
Montaje seguro
Tener en cuenta estas indicaciones de seguridad al
montar el aparato.
¡ Lea atentamente estas instrucciones.
¡ Las imágenes representadas en estas instruccio-
¡ Solamente un montaje profesional conforme a las
Un escape de gas puede provocar una explosión.
▶
shows the
16
¡ Garantizar una ventilación adecuada de la cocina;
¡ No conectar el aparato a un dispositivo de eva-
¡ No instalar el aparato en embarcaciones o vehícu-
¡ La garantía únicamente tendrá validez en caso de
When adjusting the bypass screws (M), refer to
the table → Fig.
.
16
A: Firmly tighten the bypass screws.
‒
B: The bypass screws must be flush with the fit-
‒
ting.
→ Fig.
14
Remove all pan supports, burner caps and distrib-
utors.
Replace the nozzles using the appropriate wrench
and tighten them carefully to guarantee the seal.
→ Fig.
15
Ensure that the nozzle does not become detached
during removal or fastening.
Install the appliance components in reverse order.
Check that turning the rotary knob between the
position for maximum power and the position for
minimum power does not cause the burner to go
out or result in backfire.
If the gas flow from the burner is not correct, in
the table → Fig.
, check whether the nozzle and
16
the position of the bypass screw are correct.
Attach the sticker showing the new gas type near
to the rating plate.
es
nes tienen carácter orientativo.
instrucciones de montaje puede garantizar un uso
seguro del aparato. El instalador es responsable
del funcionamiento perfecto en el lugar de instala-
ción.
ADVERTENCIA ‒ Riesgo de explosión!
Todos los trabajos de instalación, conexión, regu-
lación y adaptación a otro tipo de gas deben ser
realizados por un técnico especialista autorizado y
de conformidad con los reglamentos y disposicio-
nes legales vigentes y los reglamentos de las
compañías locales suministradoras de electrici-
dad y gas. Debe prestarse especial atención a la
normativa aplicable a la ventilación. Para los tra-
bajos de adaptación a otro tipo de gas, recomen-
damos ponerse en contacto con el Servicio de
Atención al Cliente.
en particular, durante el funcionamiento del apara-
to.
cuación de los productos de combustión.
los.
que se respete el uso para el que fue diseñado el
aparato.
9
Publicité
