Publicité
Note:
The operating mode LED indicator (4b) will automatically turn off
about 10 s after work stops.
Tool fastening
When mounting tools, always make sure that these attachments are
mounted on a ½" spindle [5] or to a transfer adapter all the way.
12.6 Mounting a belt clip
Place the machine on a horizontal surface (e.g. a working table). Slide
the bent end of the belt clip [7a] into the base for the belt clip [7c].
Secure the belt clip [7a] using a fastening screw [7b] and a correspond‑
ing screwdriver. You can mount the belt clip to the machine from the
right, as well as the left side. Be careful not to mount the belt clip
the wrong way round. The belt clip position must correspond to the
illustration.
13 Checking Accumulator Status
The battery is fitted with a charge status control panel [B3].
Press the control button [B4] on the accumulator status panel [B3]. An
accumulator status indicator [B5] will light up based on the state of
charge (capacity) of the accumulator.
Overview of accumulator's state of charge (capacity) indication:
Number of fully lit LEDs
3
2
1
14 Electronic Safeguards
The machine is fitted with circuitry designed to prevent serious dam‑
age to the machine. If the electronics detect any of the faults/defects
below, the machine stops immediately. Remove the fault/defect by
proceeding in accordance with the table.
Overview of safety features and methods for returning the machine to operation:
Type of safety feature
Low accumulator voltage
(indicated on the accumulator)
Machine overload (machine
was switched off due to recoil or
excessive load)
Overheating (critical temperature
of the motor, the electronics or
the accumulator was reached)
15 Maintenance and service
15.1 Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes of
the device. Use protective goggles for this operation. Clean the exter‑
nal plastic parts by a wet rag and mild detergent. Though these parts
are made of the materials resistant to solvents, NEVER use any solvent.
15.2 Instructions for cleaning the charger
ATTENTION!
Risk of electric shock. Prior to start han-
dling the charger, disconnect the line plug from the
socket!
Impurities and dust can be removed from external charger surfaces by
a rag or a non‑metal brush. Use neither water nor detergents.
ATTENTION!
With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case re-
moval must be performed by the authorized service cen-
tre only!
The current list of authorized service centres can be found at our web‑
site www.narex.cz.
Accumulator's state of charge
100 %
less than 60 %
less than 30 %
Solution
Recharge / replace the
accumulator
Release and then press the
power switch again
Let the machine cool off
16 Accessories
The accessories recommended for use with this device are available
commercially in the shops with hand el. tools.
17 Storage
Packed appliance may be stored in dry, unheated storage place with
temperature not lower than ‑5 °C.
Unpacked appliance should be stored only in dry storage place with
temperature not lower than +5 °C with exclusion of all sudden tem‑
perature changes.
18 Environmental protection
Power tools, accessories and packaging should be sorted for environ‑
mental‑friendly recy.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electrical
and electronic equipment and its incorporation into national law,
power tools that are no longer suitable for must be separately collect‑
ed and sent for recovery in an environmental‑friendly manner.
19 Warranty
Our equipment is under warranty for at least 12 months with regard to
material or production faults in accordance with national legislation. In
the EU countries, the warranty period for exclusively private use is 24
months (an invoice or delivery note is required as proof of purchase).
Damage resulting from, in particular, normal wear and tear, overload‑
ing, improper handling, or caused by the user or other damage caused
by not following the operating instructions, or any fault acknowl‑
edged at the time of purchase, is not covered by the warranty.
Complaints will only be acknowledged if the equipment has not been
dismantled before being sent back to the suppliers or to an authorised
NAREX customer support workshop. Store the operating instructions,
safety notes, spare parts list and proof of purchase in a safe place. In
addition, the manufacturer's current warranty conditions apply.
Note
Due to continuous research and development work, we reserve the
right to make changes to the technical content of this documentation.
20 Certificate of Conformity
CSR 350-3S:
We declare that the device meets requirements of the following stand‑
ards and directives.
Safety:
EN 62841‑1:2015
EN 62841‑2‑2:2014
Directive 2006/42/EC
Electromagnetic compatibility:
EN 55014‑1: 2017
EN 55014‑2: 2015
Directive 2014/30/EU
RoHS:
Directive 2011/65/EU
Place of storage of the technical documentation:
Narex s.r.o., Chelčického 1932, 470 01 Česká Lípa, Czech Republic
2023
Narex s.r.o.
Chelčického 1932
470 01 Česká Lípa
English
Jaroslav Hybner
CEO of the company
Juny 1, 2023
23
Publicité
