Publicité
Les langues disponibles
Les langues disponibles
7. PROGRAM FUNCTIONS
7.1 . Powering on
Connect your appliance to the main supply,
all indicator lights of the display board will
light up for 1second and then enter the clock
setting state. Default time show 12:00, hour
"12" flashes, the system clock setting icon
"
" flashes, and the system clock icon "
is always on. The clock can be input at this
time, refer to clock setting requirement for details.
After 10 seconds without any operation and the
oven will enter to adjust minute automatically.
Within 10 seconds without any operation when
adjusting minute, the oven will enter standby
mode automatically.
7.2 Time setting
In the standby mode, touching the "
button once to enter the system clock setting
state. At this time, the hour value of the
clock and the setting icon "
time) and the hour is set by rotating the
switch KB2. (0~23~0 is recyclable)
After adjusting the hours, re-touch "
to switch to minute adjustment. Minute
value and the setting icon "
time, you can set minute time by rotating
programming switch KB2.(0~59).
After adjusting the minutes, re-touch the
"
" to confirm, clock setting accomplished.
And at this time, the clock setting icon "
goes out and the second icon " : " flashes
(1s/1 time).
7.3 Function choices
Under standby status, switch different
functions by rotating the programming
switch KB1 in turn, refer to shown below for the
order. (The oven will remember the last
operation)
When selecting the function, the clock position shows the
default cooking time of the corresponding function
(it will show "Eco" under Eco mode), the temperature
position shows the default temperature of the corres-
ponding function. For temperature adjustable function
mode, temperature place will display default temperature
value of corresponding function and flash, temperature
icon "
" will flash, and the working parameter setting
www.linarie.com.au
"
"
" flash (1s/1
"
" flash at this
"
Initial standby mode
Under the standby mode, the display always shows
system time.(Refer to image below.)
When the oven is powered on, the oven door lock will
start to self-inspection. During the self-inspection, the
door lock will run back and forth automatically. If there
is no abnormal alarm within 20 seconds, then
self-inspection is completed. Or if it shows fault code
"E-3" during the self-inspection, please refer to protection
function for problem analysis, you can touch "
cancel the fault code and return to standby mode.
When the hour and minute are set, the
system clock setting icon "
the system clock icon "
After confirming, the setting icon "
off and the system clock icon "
to be displayed. In the hour setting, if you do
not touch the "
10 seconds, it will automatically switch to
the minute setting. If the "
confirmed within 10 seconds after the clock
setting is completed, the system defaults to
complete the clock setting and automatically
returns to the standby state. If the clock is
not set within 20 seconds after power-on,
the system default clock is 12:00 and enters
standby state. If the power is turned off, the
clock will be reset.
In the standby state, only the system clock
is dsplayed.
icon "
" flash as well as the oven working icon
"
" is always on. You can rotate the
programming switch KB2 to set the cooking
temperature.
If temperature is not adjustable for that switch KB2 to
set the cooking temperature. function level, the default
clock value and the working parameter setting icon
" flash as well as the oven working icon "
"
is always on.
For temperature adjustable function mode, after the
cooking temperature is set, touch "
cooking time adjustment, display screen clock place
will display default cooking time of corresponding
function and flash, the working parameter setting icon
" flash and working time icon "
"
you can rotate programming switch KB2 to set the
cooking time at this time.
10
" flashes and
" is always on.
" is
" continues
" button to confirm within
" button is not
" to switch to
" to
"
" is always on,
Publicité
