Publicité
II]
POWER switch and power/standby indicator
Immediately after turning ON the power, the standby
indicator lights in red as the built-in muting circuit
activates.
When the amplifier stays in a stable operating condition,
the indicator lights in green.
The indicator lights in red when the unit detects shorting
of circuit of the speaker outputs or in case of short-circuit
of the inputs of DC components.
In such a case, disconnect the power source and check
the connected components and speaker systems.
[I]
SPEAKERS selector
Select speaker system A or B, or both.
To use power amplifier or active speaker system
connected to the PRE OUT jacks, set the selector to B/
PRE OUT (TA-F730ES/F333ESR only).
For headphone monitoring only, set the selector to OFF.
W
ADAPTOR/DIRECT IN switch (TA-F530ES/F222ESR/
F730ES/F333ESR only)
Set to NORMAL to select program source by INPUT
SELECTOR. To listen to a program source processed
through adapter (graphic equalizer, for example)
connected to ADAPTOR jacks, set the selector to
ADAPTOR.
To listen to a program source connected to DIRECT IN
jacks, set it to DIRECT IN.
Note that selecting ADAPTOR has no effect upon the
signals output through the REC OUT jacks.
[TI
INPUT SELECTOR (TA-F530ES/F222ESR/F730ES/
F333ESR only)
Selects the desired program source.
[[] ATTENUATOR knob
Regulates the sound level.
W
MUTING switch and indicator
Generally, keep the switch released (OFF).
Depress the switch to reduce the sound level by 20 dB.
(Output voltage becomes 1/10.)
[I]
HEADPHONES jack (stereo phone jack)
[[] MODE selector
STEREO: For listening to a stereo program.
MONO: For listening to a monaural program.
W
BASS and TREBLE controls
[!Ql
REC OUT SELECTOR
Selects the program source sent to the REC OUT jacks
(rear panel).
When set to DIGIT AL, the selection is made with the
DIGITL INPUT SELECTOR. (T A-630ESD/F303ESD
only)
[TI]
BALANCE control
Controls the sound level of left and right speakers.
fill
SOURCE DIRECT switch and indicator
Depress the switch. The red indicator lights and the
circuits of the tone control, subsonic filter switch (TA-
F730ES/F333ESR), balance control and mode switch are
disengaged without regard to the setting of the switches.
When this switch is activated, the indicator of the TONE
switch does not light. (TA-F730ES/F333ESR only)
IT1J
CARTRIDGE selector (T A-F530ES/F222ESR/
F630ESD/303ESD only)
Set the selector according to your cartridge.
MM: For moving-magnet type cartridge
MC: For moving-coil type cartridge
fill
DIGIT AL INPUT SELECTOR (T A-F630ESD/F303ESD
only)
Selects the desired digital program source. When set to
ANALOG, selection is made with the ANALOG INPUT
SELECTOR.
[Ifil
SAMPLING FREQ (frequency) indicator (TA-
F630ESD/F303ESD only)
When a digital signal is being input correctly, the
sampling frequency of the signal is displayed (44.1 kHz is
displayed when CD player is being played).
The indicator lights in a second after the DIGIT AL INPUT
is selected and the program source starts at the same
time.
[1fil
ANALOG INPUT SELECTOR (TA-F630ESD/F303ESD
only)
Selects the desired analog program source. The
selection is made only when the DIGITAL INPUT
SELECTOR is set to ANALOG.
(m
TONE switch and indicator (T A-F730ES/F333ESR
only)
Depress the switch to activate the tone control circuit.
Red indicator lights.
[!ID
SUBSONIC filter switch (TA-F730ES/F333ESR only)
Depress the switch to reduce unwanted noise
components of less than 15 Hz, which cause modulation
noise.
fill
TURNOVER frequency selection switches (TA-
F730ES/F333ESR only)
Switch the turnover frequency.
~
CARTRIDGE LOAD selector (TA-F730ES/F333ESR
only)
Set the selector according to your cartridge.
MM: For moving-magnet type cartridge
MC: For moving-coil type cartridge
40
n:
For a cartridge with an impedance of 40
ohms or more.
3
Q:
For a cartridge with an impedance of 3 ohms
to 40 ohms.
9
Publicité
