Cameo CLPFLAT1RGBWIR Manuel D'utilisation page 15

PL
MODE wybór funkcji Standalone, trybów DMX i adresu DMX oraz trybu pracy Slave. ENTER umożliwia zmianę wartości i potwierdzanie zmian
wartości. Użyć przycisków UP i DOWN, aby np. ustawić mieszanie kolorów, prędkość efektu stroboskopowego lub zmienić adres DMX.
IT
MODE consente di selezionare le funzioni standalone, la modalità DMX, l'indirizzo DMX e la modalità slave. ENTER consente di modificare un
valore e di confermarne le modifiche. Premere i tasti UP e DOWN per modificare ad esempio il mix di colori, la velocità stroboscopica o l'indirizzo
DMX.
OPERATION / BEDIENUNG / UTILISATION / OPERACIÓN / OBSŁUGA / UTILIZZO
EN
NOTE
A few seconds after the spot has been correctly connected to the mains, it is ready for use and starts with the mode that was previously selected.
STATIC COLOUR
This mode offers the ability to separately adjust the brightness of the 4 LED groups R, G, B, W and to thus generate an unlimited number of different
colours (colour mixing). Press the MODE button repeatedly until "C000" appears on the display. Press ENTER and then use the UP and DOWN buttons
to select the desired colour or the strobe effect and press again on ENTER (C1 = red, C2 = green, C3 = blue, C4 = white, CF = strobe effect) The
following two digits indicate the brightness or the strobe speed (00 - 99). Using the UP and DOWN buttons, select the desired value and confirm with
ENTER. For example: If you set C1, C2, C3 and C4 to "00", all LEDs in the spotlight are off (Blackout). If you set C1 to "99" and C2, C3 and C4 to "00",
then the spotlight emits 100% red. The strobe effect is disabled with a value of CF00, CF01 corresponds to approx. 1 Hz and CF99 to approx. 20 Hz
of flash frequency.
RED 00-99 GREEN 00-99
COLOUR MACROS
In this mode, one of 15 different colours can be selected as a preset. Press the MODE button repeatedly until "CMxx" appears on the display. Press
the ENTER button and then use the UP and DOWN buttons to select the desired preset. Confirm your selection by pressing ENTER.
CM01 Red
CM02 Amber
CM03 Yellow warm
CM04 Yellow
CM05 Green
COLOUR CHANGE
Press the MODE button repeatedly until "JU00" appears on the display. Afterwards, press ENTER and then use the UP and DOWN buttons to choose
the colour change speed (display flashes, JU00 - JU99). Confirm with ENTER. To set the strobe speed, press the UP and DOWN buttons to select the
"JFxx" menu item, confirm with ENTER (display flashes) and then using the UP and DOWN buttons, set the value as desired (JF00 = strobe disabled,
JF01 corresponds to approx. 1 Hz and JF99 to approx. 20 Hz flash frequency). Press ENTER again to confirm.
COLOUR CHANGE STROBE
00-99 00-99
COLOUR BLENDING
Press the MODE button repeatedly until "FA00" appears on the display. Afterwards, press ENTER twice and then use the UP and DOWN buttons to
choose the colour blending speed (display flashes, FA00 - FA99). Confirm with ENTER. To set the strobe speed, press the UP and DOWN buttons to
select the "FFxx" menu item, confirm with ENTER (display flashes) and then using the UP and DOWN buttons, set the value as desired (FF00 = strobe
disabled, FF01 corresponds to approx. 1 Hz and FF99 to approx. 20 Hz flash frequency). Press ENTER again to confirm.
COLOUR BLENDING STROBE
00-99 00-99
AUTO MODE
Press the MODE button repeatedly until "AUTO" appears on the display. In this operating mode, the light switches automatically between colour
change and colour blending mode. The speed of the colour change or colour blending is determined by the settings of the respective mode.
BLUE 00-99
CM06 Turquoise CM11 Magenta
CM07 Cyan CM12 Pink
CM08 Blue CM13 Warm White
CM09 Lavender CM14 White
CM10 Mauve CM15 Cold White
WHITE 00-99 STROBE 00-99
15