Publicité
Wire connector pins are bent.
symptom
Valve wiring is damaged.
Lights or blower
Control module switch in
won't function (if
wrong position.
symptom
equipped).
COM switch is unplugged.
Lights or blower
Control module switch in
won't function (if
wrong position.
equipped).
Flames are very
Door is ajar.
COM switch is unplugged.
aggressive.
Venting action is too great.
Flames are very
Door is ajar.
aggressive.
Appliance won't per-
No power to the system.
Venting action is too great.
form any functions.
Receiver switch in wrong
position (if equipped).
Appliance won't per-
No power to the system.
form any functions.
Transmitter isn't operational.
Receiver switch in wrong
position (if equipped).
symptom
Transmitter isn't operational.
The following applies specifi cally to the SIT system only:
symptom
Pilot will not light.
Ignition box has been locked
Makes no noise with
out.
The following applies specifi cally to the SIT system only:
no spark at pilot
burner. (Lights and
Pilot will not light.
Ignition box has been locked
blower operate, if
Makes no noise with
out.
equipped).
no spark at pilot
burner. (Lights and
blower operate, if
equipped).
note:
Starting from off, press the on button on the transmitter. After approximately 4 seconds on/off button is pressed, the ignition
board will start the spark. The atempt for ignition will last approximately 60 seconds. If there is no fl ame ignition (rectifi cation),
note:
the board will stop sparking and the board will go into lock out.
Starting from off, press the on button on the transmitter. After approximately 4 seconds on/off button is pressed, the ignition
board will start the spark. The atempt for ignition will last approximately 60 seconds. If there is no fl ame ignition (rectifi cation),
the board will stop sparking and the board will go into lock out.
symptom
The following applies specifi cally to the Maxitrol system only:
symptom
Pilot lights.
Manual override knob is in the
No gas fl ow.
"MAN" position.
The following applies specifi cally to the Maxitrol system only:
Valve is not functioning properly.
Pilot lights.
Manual override knob is in the
No gas fl ow.
"MAN" position.
Valve is not functioning properly.
No spark after pilot
Minimal voltage from thermocou-
ignition. Valve turns off
ple or resistance in circuit ports
in one minute and does
(Parts include: "ON/OFF" switch,
not operate.
receiver, thermocurrent connec-
No spark after pilot
Minimal voltage from thermocou-
tions or temperature switches).
ignition. Valve turns off
ple or resistance in circuit ports
in one minute and does
(Parts include: "ON/OFF" switch,
No pilot ignition
Switch is in "OFF" position on
not operate.
receiver, thermocurrent connec-
(5 second continuous
the valve.
tions or temperature switches).
beep).
Wiring is loose.
No pilot ignition
Switch is in "OFF" position on
Receiver (if equipped).
(5 second continuous
the valve.
beep).
Wiring is loose.
Receiver (if equipped).
Wire connector pins are bent.
Valve wiring is damaged.
Burner continues to
Connections are loose or dam-
Wire connector pins are bent.
-
Straighten pins.
problem
-
Replace valve.
-
Verify ON/OFF switch is in the "I" position which denotes on.
problem
-
Verify "COM" switch is plugged into the front of the control
-
Verify ON/OFF switch is in the "I" position which denotes on.
module.
-
Ensure door is secured properly.
-
Verify "COM" switch is plugged into the front of the control
module.
-
Check to ensure venting is properly sealed or restrict vent
exit with restrictor plate. (Not available in all appliances).
-
Ensure door is secured properly.
-
Check breaker to verify it's in the "on" position.
-
Check to ensure venting is properly sealed or restrict vent
exit with restrictor plate. (Not available in all appliances).
-
Verify that the 3 position switch on the receiver is in the
remote position (middle).
-
Check breaker to verify it's in the "on" position.
-
Check battery power and battery orientation.
-
Verify that the 3 position switch on the receiver is in the
remote position (middle).
problem
-
Check battery power and battery orientation.
problem
Choose one of the 3 methods below to reset the system.
1.
To reset ignition box when locked out. Turn off power supply
and remove batteries (if used) from the back up battery pack.
2.
To reset the DFC Board when the board goes into a lock
Choose one of the 3 methods below to reset the system.
out condition and the LED is blinking 3 times using the
1.
To reset ignition box when locked out. Turn off power supply
transmitter on/off button:
and remove batteries (if used) from the back up battery pack.
To reset the DFC Board when the board goes into a lock
2.
out condition and the LED is blinking 3 times using the
transmitter on/off button:
3.
To reset the DFC Board when the board goes into a lock out
condition and the LED is blinking 3 times by cycling fl ame:
To reset the DFC Board when the board goes into a lock out
3.
condition and the LED is blinking 3 times by cycling fl ame:
problem
problem
-
Turn the knob to the "ON" position.
-
Valve is on pilot fl ow. Turn to the high setting, double click the large
-
Turn the knob to the "ON" position.
fl ame button on the remote.
-
Replace valve. Do not overtighten.
-
Valve is on pilot fl ow. Turn to the high setting, double click the large
-
Measure the voltage, it should read a least 5mV. The spade
fl ame button on the remote.
connector is on the outer surface beside the magnet nut. Verify with
-
Replace valve. Do not overtighten.
manufacturer the drop time, after thermocouple is heated measure
the drop time.
-
Measure the voltage, it should read a least 5mV. The spade
connector is on the outer surface beside the magnet nut. Verify with
manufacturer the drop time, after thermocouple is heated measure
-
Switch to "ON" position.
the drop time.
-
Ensure wiring is properly secured.
-
Switch to "ON" position.
-
Reset program: hold reset button on receiver and wait for 2 beeps.
Release after second beep. Press small fl ame button on remote
-
Ensure wiring is properly secured.
within 20 seconds, you will hear an additional beep (this signals a
successful reset).
-
Reset program: hold reset button on receiver and wait for 2 beeps.
-
Replace receiver.
Release after second beep. Press small fl ame button on remote
within 20 seconds, you will hear an additional beep (this signals a
-
Straighten pins.
successful reset).
-
Replace valve.
-
Replace receiver.
-
Verify the thermocouple is clean and the wiring between it and the
-
Straighten pins.
test solution
troubleshooting
test solution
test solution
test solution
Step 1: Turn the system off by pressing the on/off
button to turn the system off.
Step 2: After approximately 2 seconds press the on/
off button on the transmitter again. The DFC Board will
Step 1: Turn the system off by pressing the on/off
reset and the ignition sequence will start again.
button to turn the system off.
Step 2: After approximately 2 seconds press the on/
off button on the transmitter again. The DFC Board will
Step 1: In the manual fl ame control mode, use the down
reset and the ignition sequence will start again.
arrow button to reduce the fl ame to off, indicated by the
word OFF displayed on the transmitter LCD screen.
Step 2: Wait approximately 2 seconds and press the up
Step 1: In the manual fl ame control mode, use the down
arrow button, the ignition sequence will start.
arrow button to reduce the fl ame to off, indicated by the
word OFF displayed on the transmitter LCD screen.
Step 2: Wait approximately 2 seconds and press the up
arrow button, the ignition sequence will start.
test solution
test solution
EN
63
W415-4192 / --1 / 02.05.24
Publicité
