Publicité
Les langues disponibles
Les langues disponibles
en
i
These installation instructions are valid in general, if you place your
pool free. If you sink your pool partially or completely, so please
check the separate instructions in the installation manual and the in-
stallation instructions enclosed.
To protect you from unnecessary surprises, it makes sense that you
make a plan before setting up the pool on what material you need
and what you want to do in a time
Do not install the swimming pool on a windy day. It is extremely diffi-
cult to keep the swimming pool wall upright and it would probably
fall, resulting in
injuries. In addition, fill the pool immediately after
installation to avoid any damage caused by rising wind, etc. The steel
wall pool must not be left unfilled.
Mount the pool liner on a warm,
sunny day, so it is easy to interpret in the pool. You shouldn't also
mount the swimming pool liner in direct sunlight, since the thermal
expansion not an optimal fit of the film is
installation of the swimming pool liner is in summer, early morning or
late
even-ing.
Do not mount the pool liner at temperatures below 15°
C, other-wise the film is stiff and difficult to assemble.
The swimming pool filter system and other accessories may be
op-erated electrically. If you do not have appropriate electrical
connec-tions in your garden, it is necessary to establish this.
The necessary electrical connections must be made by a
licensed electrical contractor. The supply lines are secure and in
addition to earth with a residual current circuit breaker 30
milliamps.
The rele-vant statutory provisions as ÖVE, VDE etc.
must be observed. Avoid sharp objects in the pool. This could
lead to damage to the film. Do not climb onto the handrail. This
could result in damage to the handrail or the pelvic
ATTENTION! Steel wall pools are not suitable for salt water! All
important questions, such as installation requirements or legal
building requirements, will be answered by your local
specialist.Swimming pools with a depth of 90 or 120 cm are not
suitable for dives or headjumps. Failure to comply could result in
severe head or spinal injuries!
Never leave your children unattended when they are in or around
the swimming pool!
Should there be children in your home or neighborhood, who can
not swim, we recommend you to set up an inexpensive mesh
fence which is available in construction stores, around your pool.
Tarpau-lins or other pool covers do not provide child safety. So do
not leave that pool covers, no matter what kind they are, get rid of
the respon-sibility for your children.
i
Location of your pool (Figure 1)
When choosing a location for your
tion of several
factors.
Under no circumstances, the swimming pool must be installed
below ground level. This swimming pool must only be installed
above ground and on a hard, solid ground.
therefore not be bolted on banked
subsidence and thus damage to the swimming
choose the sun-niest spot in your
basin, the better it is.
At least you should have an open space of
about 90 cm around the pool.
If there is the possibility of a sheltered
for your
pool.
A swimming pool which is unprotected from the wind
is subject to a high heat loss by convection and
You shouldn't place your pool
next to or
(large maintenance
effort).
Under no circumstances your pool should be installed under over-
head lines. Avoid providing your pool on land lines.
i
Location of the filter system
Your pool should be equipped with a sand filter. In free-standing
filter systems is a minimum distance from the edge of the pool to be
ob-served.
For
further
information
attached description of the filter
system.
Preparing an installation site
We want you to have your pool for many years with great pleasure.
The effort and care that you put into the preparation of the founda-
Page 6 of 38
schedule.
given.
The best time for the
wall.
pool,
you should take considera-
Your pool should
surfaces.
This could lead to
pool. If it is possible
garden.
The larger the area of the
spot, so
you should choose
evaporation.
under
trees, bushes, etc.
please
see
the
tions can make a great difference in the life span of your swimming
pool and its
liner.
The better prepared and fixed the place is, the
longer you will have to enjoy your swimming pool. Therfore we apply
appropriate care. It is absolutely necessary that the ground on which
your pool is built is flat and stable (no banked areas).
Settlements would inevitably lead to deformity and damage to your
pool.
Remove roots, grass and stones in the selected area, including
those under the ground. The weight of the water will compress these
elements between the liner and the earth under the swimming pool,
resulting in damages. Grass left underneath the pool liner will rot and
give of an unpleasant odor and stones and roots will damage the
pool liner.
If you build your pool directly on concrete, asphalt or a similar sur-
face, so it is essential that between the substrate and the film a
commercial mineral fiber fabric is introduced as a separating layer.
Never install this swimming pool inside a garage, or on a balcony,
roof, terrace or any other surface that is not completely flat and solid.
The maximum weight that the installation site can support must be
taken into consideration.
The basin is generally not suitable for installation in the ground,
there is no guarantee at contravene.
Plot the place of installation
Please refer to the dimensions according to the table and draw on
your installation location with lime powder or spray paint.
3. Hammer a peg into the ground in the center of the area where
you want your pool.
4.
Now drag a circle with a cord and a can of paint or spray with lime
powder, with the radius of which is specified in the table.
Tank size
R
Ø 3,5 m
1,75 m
Ø 4,0 m
2,0 m
Ø 4,6 m
2,30 m
Ø 5,5 m
2,75 m
R+
is the radius of the required footprint. (Figure 2,4)
3. Level the ground in the marked area. The entire area of the
swimming pool must be leveled and free of stones and twigs. (Fig-
ure 5)
Leveling the place of installation
Using a leveling tool, a straight wooden board or even better would
be a yardstick (alu slat) and level the surface down to the level of the
lowest point. Do not fill in the holes; dig away higher areas. Scatter a
fine layer of sifted sand over the levelled surface and level again. Dig
from the raised
spots.
In no case the subscript throw
lead to subsidence.
Figure 6, 7
Now pave the installation location so until this is completely flat. Only
a properly prepared installation site is a prerequisite for a functional
pool.
Using floor insulation:
If you isolate the pelvic floor with Styrofoam or Styrodur, it is neces-
sary to make the whole pool to the insulation.
Bring to a maximum of 3 cm thick, flat gravel layer and compress
them.
Then place the insulation into the bottom gravel bed.
Figure 9
Nuovo deluxe Duo rund | 2020_V2
R+ detached
R+ sunk
2,0 m
2,25 m
2,25 m
2,5 m
2,55 m
2,80 m
3,0 m
3,25 m
up,
this could
Publicité
