Publicité
still not working, try replacing the batteries.
o
Link the remote to the LivingColors by following
the procedure described in section 3.1 of this
manual.
•
Buttons are flashing after I have used the remote
control
o
This means that the batteries in the remote
control are (almost) empty and need to be
replaced.
•
I cannot start the automatic colour-changing
mode
o
It could be that the remote control did not
understand your "sweep" movement. Please
try again, making sure that your finger is on the
colour wheel during the full circle movement
•
I would like to connect the LivingColors to a
timer. Is this possible?
o
Yes. You can use Philips LivingColors with a timer
(not included). When switched on with a timer,
the LivingColors will show your last setting
(static colour or automatic colour-changing
mode). Please make sure that your last setting is
not "off".
•
I cannot connect additional lamps to the
LivingColors remote control
o
Please make sure that the product you are
trying to connect has a SmartLink logo on it.
Only products with a SmartLink logo can be
connected to this remote control.
o
Try repeating the procedure described in section
3 of this manual. Make sure you do hear the
sounds and see the flashes as described there.
•
My question is not listed here
o
Please contact Philips for assistance (see section
5 "Additional support").
5.
Additional support
For information and in the event of any problem,
please visit the Philips website at www.philips.com or
contact the Philips Lighting Contact Centre free of
charge in the: 00800-PHILIPSL or 00800-74454775
Warranty:
The Philips two-year warranty is valid if the product
is used in accordance with the instructions and for
its intended purpose. Claims will only be accepted on
submission of the original proof of purchase (invoice,
sales slip or receipt) stating the purchase date, the
name of the dealer and a description of the product.
The Philips warranty lapses if:
•
Anything has been changed, crossed out, deleted
or rendered illegible on the purchase docket or
product description.
All manuals and user guides at all-guides.com
•
The failure is caused by damage, faulty
connections or abuse.
•
A defect is caused by extreme circumstances
not inherent to the LivingColors, for example,
lightning, flooding, fire, incorrect use or
negligence.
•
The LivingColors has been opened or
disassembled.
Cleaning and maintenance:
Remove the plug from the wall socket.
To avoid scratching, the LivingColors lamp, remote
control and adapter should only be cleaned with a
soft dry cloth.
Do not use cleaning agents.
Safety instructions:
Keep the plug and LivingColors away from liquids and
humidity.
•
LivingColors is for indoor use only. Do not use
in wet locations, e.g. bathrooms or outdoors
•
LivingColors is not a toy designed to be played
with by children.
•
Do not place on hot surfaces
•
For safety reasons and under the terms of the
warranty, the LivingColors and plug must not be
opened.
•
Only use the adapter supplied: using a different
adapter can damage your LivingColors.
Environment:
If you discard the appliance in due course, dispose
of it in accordance with the instructions of the local
authority. Remove the batteries when you discard
the remote control. Do not throw the batteries away
with normal household waste. They must be handed
in at an official collection point or at a Philips Dealer,
both of which will dispose of the batteries in an
environmentally friendly way.
Plug specification:
AC adapter
Model:
EADP-10EB C (EU type)
EADP-10EB D (UK type + Singapore)
EADP-10EB E (Australia type)
Input:
110–240 V ~ 0.3 A 50 Hz
Output:
18.5 V
0.83 A
Power consumption of the luminaire: up to 15.4 W
Remote Control:
Batteries: 3 x Philips Powerlife Alkaline AAA LR03,
1.5 V.
Wireless specification:
Wireless RF mode frequency band:
2405~2475 MHz
Wireless communications protocol:IEEE 802.15.4)
19
Publicité
