Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
1.4.8 Bluetooth activation/deactivate / (bLE)
bLE = Bluetooth = off / on
To activate or deactivate bluetooth push (ENTER/MENUE). Use the up and
down keys (
) to select bLE. Push again (ENTER/MENUE). Use the up key
(
) to activate on or deactivate off the bluetooth function and push (ENTER/
MENUE) to confirm. Push (ESC) to revert back to the measuring mode.
Unit
Prob
L in 2
1.5 Recalling the memory data (HOLD MAX MIN AVE)
After pushing first time the key (HOLD MAX MIN AVE) the actual values will be
held on the display. Pushing again the key (HOLD MAX MIN AVE), the saved
maximum-, minimum and average values will be displayed.
Note: During the recall of the memory data the extremes (MAX MIN) and the
average value (AVE) will not be calculated or carried on.
Clearing the memory (MAX MIN AVE)
Press (CLEAR) key once to erase the stored maximum, minimum and average
from memory. On the display appears Clr. – After erasing the memory the
instrument automatically reverts back to measuring mode indicating the actual
measured value again.
1.6 Measuring rate (Normal-Mode / FAST-Mode / Filter-Mode)
The instrument has three different response times to select:
Normal-Mode:
high resolution
(0.001 from -199.999 to +199.999)
FAST-Mode:
reduced resolution
(0.01 from -199.99 to +199.99)
Filter-Mode:
high resolution
(0.001 from -199.999 to +199.999)
Press (FAST /
) key to change the measuring rate. By using the Filter-
Mode the instrument is performing a moving average to stabilize the dispayed
measurements. After turning on the instrument it is in the Normal-Mode. After
pressing once the (FAST /
) key the instrument switches to the Fast-Mode.
Pressing the same key once again the instrument switches to the Filter-Mode.
E.g. Display with activated Filter-Mode:
The arrow on the top indicates that the instrument is
working in the Filter-Mode.
Note: After switching off the instrument, this function is automatically deactivated.
18
MENUE
CAL
ChnI
Lo6
bLE
1.7 AUTO-OFF-function
dAoF = Disable Auto-off
EAoF = Enable Auto-off
Press (ESC/AUTO-OFF) key once. On the display appears EAoF. Now the
instrument switches off automatically after app. 30 minutes. Press (ESC/AU-
TO-OFF) key again. On the display appears dAoF. Now the Auto-Off-function
is deactivated.
Attention: This setting will be deactivated when the instrument turns off.
(Standard setting is EAoF).
1.8 TARE-Function (ZERO-Mode F1)
The Instrument has a special Tare/Zero-button. Pressing the (F1) key once, the
instrument will subtract the last measured value from the actual measured value.
So if the measurement does not change zero appears on the instrument's display.
If you press the (F1) key once again the instrument move to the Normal-Mode.
E.g. Display with activated Zero-Mode:
The arrow on the left indicates that the instrument is
working in the Zero-Mode (F1).
Note: After switching off the instrument, this function is automatically deactivated.
2. Power supply
- For the power supply of the instrument a 9 Volt dry battery is used.
To exchange the battery switch of the instrument and open the rear battery
cover. Remove the battery from the instrument and replace with a new battery.
- The "BAT" symbol in the display indicates that the battery needs to be
exchanged. After displaying the "BAT" symbol, the instrument allows
app. 1 hour of further operation.
- The battery symbol indicates according to the battery status between
1 to 3 segments.
Attention:
Please do not dispose of old electronic devices and empty batteries in household
waste. To protect the environment, take them to your retail store or to appropriate
collection sites according to national or local regulations.
19
Publicité
Chapitres
Table des Matières
