EINHELL BT-LC 400 Mode D'emploi page 13

Anleitung BT-LC 400_SPK1:_
Do not lose these safety regulations.
Guard against electric shock
Avoid body contact with earthed parts.
When equipment is not being used it should be
kept in a dry, closed place out of childrenʼs reach.
Keep mounted attachments sharp and clean to
enable you to work well and safely.
Check the power cable regularly and have it
replaced by an authorized specialist at the first
sign of any damage.
Check your extension cables regularly and
replace them if damaged.
When working outdoors, use only extension
cables that are approved for outdoor use and
which are marked accordingly.
Concentrate on what you are doing. Use common
sense when working. Do not operate the tool if
your mind is not on your work.
Never use an electric tool with a switch that
cannot be turned on and off.
Warning! The use of other tools and accessories
may put you at risk of injury.
Always pull the plug out of the power socket
before adjusting or servicing the machine.
Give these safety regulations to all persons who
work on the machine.
Caution! Hands and fingers may be injured on the
rotating saw blade.
The machine is equipped with a safety circuit-
breaker (7) to prevent it starting up again after a
voltage drop.
Before you use the machine for the first time,
check that the voltage marked on the rating plate
is the same as your mains voltage.
If you need to use an extension cable, make sure
its conductor cross-section is big enough for the
sawʼs power consumption. Minimum cross-section
1,5 mm 2 or 2,5 mm 2 for cable lengths of 20 m or
more.
If you use a cable reel, the complete cable must
be pulled off the reel.
Check the power cable. Never use a faulty or
damaged power cable.
Do not use the cable to pull the plug out of the
socket. Protect the cable from heat, oil and sharp
edges.
Do not leave the saw in the rain and never use it
in damp or wet conditions.
Provide good lighting.
Do not saw near flammable liquids or gases.
Wear suitable work clothes! Loose garments or
jewelry may become caught up in the rotating saw
blade.
Non-slip shoes are recommended when working
outdoors.
Wear a hair net if you have long hair.
12.11.2007 13:52 Uhr Seite 13
Avoid abnormal working postures.
Operators must be at least 16 years of age.
Keep children away from the machine when it is
connected to the power supply.
Keep your workplace clean of wood scrap and
any unnecessary objects.
An untidy work area invites accidents.
Do not allow other persons, especially children, to
touch the tool or cable. Keep them out of your
work area.
Persons working on the machine should not be
distracted.
Note the direction of rotation of the motor and saw
blade. Use only blades whose permissible
maximum speed is not lower than the maximum
spindle speed of the circular saw and of the
material to be cut.
After you have switched off the motor, never slow
down the saw blade (4) by applying pressure to its
side.
Only fit blades (4) which are well sharpened and
have no cracks or deformations.
Do not use circular saw blades (4) made of high-
alloy high-speed steel (HSS).
Only use saw blades that are recommended by
the manufacturer, comply with EN 847-1 and bear
a warning note. When replacing the saw blade
ensure that the cutting width is no smaller and the
basic blade thickness of the saw blade is no larger
than the thickness of the splitter.
Faulty saw blades (4) must be replaced
immediately.
Never use saw blades which do not comply with
the data specified in this manual.
Never dismantle the machineʼs safety devices or
render them inoperative.
If the table insert is worn, replace it.
Always stand to the side of the saw blade when
working with the saw.
Never load the machine so much that it cuts out.
Make sure that off-cuts do not catch on the saw
blade crown. Risk of catapulting!
Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
To rectify faults or remove jammed pieces of
wood, always switch off the machine first. Pull the
power plug!
If the sawing gap is worn, replace the table insert.
Pull the power plug!
Carry out retooling work, adjustments,
measurements and cleaning jobs only when the
motor is switched off. Pull the power plug!
Before switching on, make sure that all keys and
wrenches have been removed from the tool.
Switch off the motor and pull the power plug
before you leave the workplace.
GB
13